Lantronix ETS16PR, ETS8PS, ETS16PS, ETS32PR manual Printing on the ETS

Page 31

Printing on the ETS

5. Select LPR Port.

Note: If LPR Port is not an option, open the Network Control Panel and add “Microsoft TCP/IP Printing” to the List of services.

6.Enter the name or IP address of your ETS on the first line, and enter the name of your ETS print service on the second line.

7.Select the manufacturer and printer type.

8. Enter the queue name.

ETS Installation Guide

31

Image 31

Contents ETS Installation Guide Technical Support Lantronix Corporate HeadquartersSales Offices Disclaimer and Revisions Contents LAT Configuration Contents SpecificationsRS-423 IntroductionSupported Serial Protocols RS-232Introduction How to Use This ManualETS8PS/ETS16PS LEDs InstallationEtsp Product Descriptions Etsps Front PanelsInstallation Installing the EtspETS16PS Back Panel ETS16PR Front Panel Etspr Product DescriptionsETS32PR Front Panel Installing the EtsprEtspr LEDs Sample Etspr Network Layout ETS16PR shown Installation EZWebCon Configuration MethodsUsing a Web Browser Etspr models Getting StartedConsole Terminal TCP/IP ConfigurationIncoming Logins Using EZWebConARP and Ping on Unix Using a Directed Ping PacketUsing a BOOTP, DHCP, or Rarp Reply Was the Installation Successful?Using the Command Line Interface Console Server Example Using the ETSDefine the Menus Using the ETSConfigure Switches Enable Menu Mode10. Configuring Switches Using MenusSerial Tunnel Example TCP ConfigurationMulti-port Serial Tunnel Configuration UDP ConfigurationComm Port Redirector LPR on Windows 2000, XP, ServicesPrinting on the ETS LPR PrintingPrinting on the ETS To enable LPR support, install Print Services for UnixPrinting on the ETS Printing on the ETS Local Define Service ETSHPLaserjet port Enable LPR on Windows NT 3.5.1 and later Printing on the ETS LPR on Unix Hosts LPR on Windows 95/98Adding /etc/hosts Entry LPR on AIX HostsLPR on SCO Unix Hosts LPR on HP HostsAnswer the questions that follow Rtel FunctionalityArea to Check Explanation Unix Host TroubleshootingObtain an NDS License NetWare ConfigurationConfigure your ETS Ndps Printing NDS Print QueuesPconsole Print Queues NetWare Administrator Quick Setup Print QueuesNetWare Configuration From the Menu Bar, select Tools Print Services Quick SetupUse the Show Protocols NetWare Access NetWare Host TroubleshootingCode Meaning Remedy NetWare Configuration LAT Host Troubleshooting LAT ConfigurationPrinting Directly to a Port Translating LAT Error Codes LAT ConfigurationAppleTalk Zones AppleTalk ConfigurationMacintosh Services BitronicsAppleTalk Configuration AppleTalk Host TroubleshootingHost Configuration DLC Configuration for LAN ManagerDLC Configuration ETS ConfigurationTechnical Support Europe, Middle East, and Africa Contact InformationPower-up Troubleshooting TroubleshootingBootp Troubleshooting Dhcp TroubleshootingTroubleshooting Entering Commands at the Boot Prompt Rarp TroubleshootingFlash SET Bootp Enabled, DisabledSET Dhcp Enabled, Disabled Flush NVRShow Server Troubleshooting SET Rarp Enabled, DisabledSET Secondary ipaddress SET Software filenameRJ45 to DB25 Ethernet ConnectorRJ45 Serial Connectors PinoutsFigure C-3. Pinouts of RJ45-DB25 Connections PinoutsRJ45 to DB9 Figure C-5. Wire SplicerVia the Web Via FTP Updating SoftwareChoosing the Right Software File Obtaining SoftwareReloading Sequence Reloading SoftwareUpdating Software MOP NetWareTftp Troubleshooting Flash ROM UpdatesPower Information SpecificationsEnvironmental Limitations Server Commands Frequently-Used CommandsConventions Nopassword Frequently-Used CommandsBanner Zero Counters ALL Port CommandsSHOW/MONITOR Port Protocol CommandsNetware Etherii Declaration of Conformity Compliance and Warranty InformationCompliance and Warranty Information Warranty