Lantronix 900-653-R manual Password Press Enter for Setup Mode

Page 37

6: Configuration Via Telnet or Serial Port (Setup Mode)

Password :----

Press Enter for Setup Mode

3.Enter User Name (user name is admin and cannot be changed). Pressing the Enter key after entry is not necessary. The Password field will appear.

4.Enter Password (default password is PASS). Pressing the Enter key after entry is not necessary. You will be prompted to enter Setup Mode.

Note: Password can be modified or disabled. See Server Configuration (on page 26).

5.To enter Setup Mode, press Enter within 5 seconds. The configuration settings display (see Figure 6-2), followed by the Change Setup menu.

Figure 6-2 Setup Menu Options

*** basic parameters Hardware: Ethernet TPI

IP addr - 0.0.0.0/DHCP/BOOTP/AutoIP, no gateway set DNS Server not set

Telnet config password set DHCP device name : not set DHCP FQDN option: Disabled

*** Security
SNMP is	enabled
SNMP Community Name:	public
Telnet Setup is	enabled
TFTP Download is	enabled
Port 77FEh is	enabled
Web Server is	enabled
Web Setup is	enabled
ECHO is	disabled
Encryption is	disabled
Enhanced Password is	disabled

*** Channel 1
Baudrate 9600,	I/F	Mode 4C, Flow 00
Port 10001
Connect Mode :	C0
Send ‘+++’ in Modem Mode enabled
Show IP addr after		‘RING’ enabled
Auto increment	source port disabled
Remote IP adr:	---	none ---, Port 00000
Disconn Mode :	00
Flush Mode :	00
*** Expert
TCP Keepalive	:	45s
ARP cache timeout:		600s
CPU performance: Regular
Monitor Mode @	bootup : enabled
HTTP Port Number :		80
MTU Size: 1400

xDirect User Guide

37

Image 37

Contents User Guide Copyright & Trademark WarrantyContacts DisclaimerUsing this Guide Table of ContentsInstallation of xDirect Using DeviceInstallerConfiguration Via Telnet or Serial Port Setup Mode Configuration Using Web ManagerSetup Mode Channel Configuration Setup Mode Server ConfigurationFirmware Upgrades Setup Mode Advanced SettingsMonitor Mode Appendix B Connections and Pinouts Appendix a Troubleshooting and Contact InfoAppendix E Binary to Hexadecimal Conversions Appendix F ComplianceSerial Tunneling Example List of FiguresList of Tables Purpose and Audience Using this GuideChapter Summary Document Description Additional DocumentationIntroduction Key FeaturesApplications Introduction Configuration Methods Additional FeaturesProtocol Support Product Label Product Information LabelPackage Contents Installation of xDirectInstalling the xDirect Hardware Address Required InformationIP Address Installing DeviceInstaller Using DeviceInstallerTo install DeviceInstaller Assigning an IP AddressViewing the Current Configuration Accessing the xDirect Using DeviceInstallerTo view the units current settings XDirect Configuration in DeviceInstallerComments Supports Configurable PinsDevice Family TypeNext Step Assigning the IP Address Serial Port LoginAccessing xDirect Using DeviceInstaller Configuration Using Web ManagerConfiguration Using Web Manager Network Mode Network ConfigurationAutomatic IP Address Configuration To assign an IP address automaticallyEthernet Configuration Static IP Address ConfigurationSelect Use the following IP configuration To assign an IP address manuallyTo configure the xDirect device server settings Server ConfigurationCPU Performance Mode Monitor Mode @ BootupConfig Server Port Timeout msTo configure the host list Host List ConfigurationRetry Timeout Retry CounterSerial Settings Channel 1 ConfigurationTo configure the channel’s serial settings Baud Rate Enable PackingData Bits ParityTo configure a channel’s TCP settings Connection Settings TCPAccept Incoming Modem Mode Password RequiredModem Escape Sequence Pass ThroughTo configure a channel’s UDP settings Connection Settings UDPUse Broadcast Datagram TypeDevice Address Table Apply Defaults Apply SettingsAccessing Setup Mode Configuration Via Telnet or Serial Port Setup ModeTelnet Connection To establish a Telnet connectionPassword Press Enter for Setup Mode Two options through which to exit setup mode Exiting Setup ModeSerial Port Connection Server Configuration Option Setup Mode Server ConfigurationBootP/DHCP/AutoIP options IP AddressNetmask Number of Bits for Host Part Set Gateway IP AddressSet DNS Server IP Address Standard IP Network NetmasksDhcp Name Change Telnet Configuration PasswordChannel 1 Option Setup Mode Channel ConfigurationBaudrate Interface Mode Options Interface ModeCommon Interface Mode Settings FlowPort Number Connect ModeFlow Control Options Reserved Port NumbersConnect Mode Option Connect Mode OptionsIncoming Connection Active Startup ResponseManual Connection Address Example C0.0.0.0/0 Host List Option HostlistAutostart Automatic ConnectionTo enable the hostlist Modem ModeDatagram Type Directed UDPMessage Meaning Modem Mode Messages10 Modem Mode Commands Send the Escape Sequence +++ in Modem ModeModem Mode Function Command Show IP Address after RingAuto Increment Source Port Disconnect Mode DisConnModeRemote IP Address Remote Port11 Disconnect Mode Options Flush Mode Buffer Flushing12 Flush Mode Options Packing Interval Pack ControlTrailing Characters Send CharactersChannel Port Password DisConnTime Inactivity TimeoutSend Characters Telnet Terminal TypeExpert Settings Option Setup Mode Advanced SettingsARP Cache Timeout In Seconds TCP Keepalive Time In SecondsSecurity Settings Option Disable Telnet Setup Disable SnmpSnmp Community Name Disable Port 77FE Hex Disable Tftp Firmware UpdateDisable Web Server Disable Web SetupEnable Enhanced Password Default Settings OptionExpert Settings Defaults Channel 1 Configuration DefaultsSecurity Settings Defaults Setup Mode Advanced SettingsUsing Tftp Graphical User Interface Firmware UpgradesObtaining Firmware Reloading Firmware Firmware FilesTo recover firmware Using Tftp Command Line InterfaceFirmware Upgrades Entering Monitor Mode Using the Serial Port Monitor ModeEntering Monitor Mode Using the Network Port To enter Monitor Mode locallyMonitor Mode Commands Monitor Mode CommandsCommand Command Name Function G0, G1, ....,Ge, GfResponse Meaning Command Response CodesLEDs Appendix a Troubleshooting and Contact InfoStatus LED Table A-2 Status LEDSerial LEDs Problems and Error MessagesRJ45 Ethernet LED Using DeviceInstaller Serial Settings on page 29 or United States Technical SupportEurope, Middle East and Africa Serial Port Pinouts Appendix B Connections and PinoutsTable B-6 Ethernet RJ45 Connector Pin-Outs Ethernet Connector PinoutsPower Jack Mini USB-B Table C-1 xDirect Technical Specifications Appendix C Technical SpecificationsCategory Description Appendix C Technical Specifications AutoIP Appendix D Alternative Ways to Assign an IP AddressTo assign a temporary IP address ARP and TelnetConverting Binary to Hexadecimal Appendix E Binary to Hexadecimal ConversionsConversion Table Scientific CalculatorAppendix E Binary to Hexadecimal Conversions Appendix F Compliance SafetyManufacturer’s Name & Address Electromagnetic EmissionsRoHS Notice Appendix F Compliance