Lantronix 900-653-R manual Appendix C Technical Specifications, Category Description

Page 75

Appendix C: Technical Specifications

 

 

Table C-1 xDirect Technical Specifications

 

 

 

 

Category

Description

 

CONTROLLER

 

 

 

 

 

CPU

Lantronix DSTni-EX enhanced 16-bit x86 architecture, 48 MHz clock

 

 

 

 

MEMORY

 

 

 

 

 

Internal CPU Memory

256 KB zero wait state SRAM

 

 

 

 

Flash

8 Mbits (1 MB)

 

 

 

 

POWER INPUT1,2

 

 

1 Mini USB-B jack

Accepts 5 VDC Wall Adapter (included in non-PoE models)

 

 

Pin 1 (+) and pin 4, 5 (-)

 

 

Data pins = no connection

 

 

Note: User can also use USB powering from a PC as long as the USB source is

 

 

able to provide 5V 500mA with no requirement for power negotiation

 

 

 

 

1 DB9F Redundant Powering

5 to 15 VDC

 

 

Pin 9 (+) and pin 5 (-)

 

 

Note: If using a null modem gender (Lantronix P/N 140-448-R), Pin 9 can be

 

 

used to power the unit.

 

 

 

 

Optional PoE Redundant

IEEE 802.3af PoE standard-compliant PD

 

Powering via Ethernet RJ45

Powering via data pins or spare pins

 

Connector (PoE version only)

Magnetic Isolation 1500 VAC between Ethernet connection and internal logic

 

 

Note: See ordering part number for PoE option on Lantronix website

 

 

 

 

LED Indicator (amber “X”)

Power/Status

 

 

 

 

Power Rating

1.3W max with no PoE

 

 

2.0W max with PoE option

 

 

 

 

SERIAL INTERFACE

 

 

 

 

 

1 DB9F Connector

DCE serial port

 

 

Software-selectable baud rate from 300 to 921 Kbaud

 

 

Software-selectable RS232, RS422 or RS485 (2 and 4 wire support)

 

 

Redundant powering from pin 9 (+) and pin 5 (-), 5V to 15 VDC

 

 

15kV HBM ESD protection on RS232 and RS422/485 transceivers

 

 

 

 

Serial Line Formats

Characters: 7 or 8 data bits

 

 

Stop bits: 1 or 2

 

 

Parity: odd, even, none

 

 

 

 

Modem Control

DTR, DSR

 

 

 

 

Flow Control

Hardware: CTS/RTS

 

 

Software: XON/XOFF

 

 

 

 

LEDs for Serial Data

Transmit and Receive Activities:

 

 

Green: indicates transmission activity

 

 

Amber: indicates reception activity

 

 

 

 

 

 

xDirect User Guide

75

Page 74 Page 76
Image 75
Page 74 Page 76
Contents User Guide Disclaimer WarrantyCopyright & Trademark ContactsUsing DeviceInstaller Table of ContentsUsing this Guide Installation of xDirectConfiguration Via Telnet or Serial Port Setup Mode Configuration Using Web ManagerSetup Mode Channel Configuration Setup Mode Server ConfigurationSetup Mode Advanced Settings Firmware UpgradesMonitor Mode Appendix F Compliance Appendix a Troubleshooting and Contact InfoAppendix B Connections and Pinouts Appendix E Binary to Hexadecimal ConversionsSerial Tunneling Example List of FiguresList of Tables Using this Guide Purpose and AudienceChapter Summary Document Description Additional DocumentationKey Features IntroductionApplications Introduction Additional Features Configuration MethodsProtocol Support Product Label Product Information LabelInstallation of xDirect Package ContentsInstalling the xDirect Required Information Hardware AddressIP Address Assigning an IP Address Using DeviceInstallerInstalling DeviceInstaller To install DeviceInstallerXDirect Configuration in DeviceInstaller Accessing the xDirect Using DeviceInstallerViewing the Current Configuration To view the units current settingsType Supports Configurable PinsComments Device FamilyNext Step Assigning the IP Address Serial Port LoginAccessing xDirect Using DeviceInstaller Configuration Using Web ManagerConfiguration Using Web Manager To assign an IP address automatically Network ConfigurationNetwork Mode Automatic IP Address ConfigurationTo assign an IP address manually Static IP Address ConfigurationEthernet Configuration Select Use the following IP configurationTo configure the xDirect device server settings Server ConfigurationTimeout ms Monitor Mode @ BootupCPU Performance Mode Config Server PortRetry Counter Host List ConfigurationTo configure the host list Retry TimeoutChannel 1 Configuration Serial SettingsTo configure the channel’s serial settings Parity Enable PackingBaud Rate Data BitsConnection Settings TCP To configure a channel’s TCP settingsAccept Incoming Pass Through Password RequiredModem Mode Modem Escape SequenceTo configure a channel’s UDP settings Connection Settings UDPDatagram Type Use BroadcastDevice Address Table Apply Defaults Apply SettingsTo establish a Telnet connection Configuration Via Telnet or Serial Port Setup ModeAccessing Setup Mode Telnet ConnectionPassword Press Enter for Setup Mode Exiting Setup Mode Two options through which to exit setup modeSerial Port Connection IP Address Setup Mode Server ConfigurationServer Configuration Option BootP/DHCP/AutoIP optionsStandard IP Network Netmasks Set Gateway IP AddressNetmask Number of Bits for Host Part Set DNS Server IP AddressDhcp Name Change Telnet Configuration PasswordSetup Mode Channel Configuration Channel 1 OptionBaudrate Flow Interface ModeInterface Mode Options Common Interface Mode SettingsReserved Port Numbers Connect ModePort Number Flow Control OptionsConnect Mode Options Connect Mode OptionIncoming Connection Response Active StartupManual Connection Address Example Connection Host List Option HostlistC0.0.0.0/0 Autostart AutomaticDirected UDP Modem ModeTo enable the hostlist Datagram TypeMessage Meaning Modem Mode MessagesShow IP Address after Ring Send the Escape Sequence +++ in Modem Mode10 Modem Mode Commands Modem Mode Function CommandRemote Port Disconnect Mode DisConnModeAuto Increment Source Port Remote IP AddressFlush Mode Buffer Flushing 11 Disconnect Mode Options12 Flush Mode Options Send Characters Pack ControlPacking Interval Trailing CharactersTelnet Terminal Type DisConnTime Inactivity TimeoutChannel Port Password Send CharactersTCP Keepalive Time In Seconds Setup Mode Advanced SettingsExpert Settings Option ARP Cache Timeout In SecondsSecurity Settings Option Disable Snmp Disable Telnet SetupSnmp Community Name Disable Web Setup Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web ServerEnable Enhanced Password Default Settings OptionSetup Mode Advanced Settings Channel 1 Configuration DefaultsExpert Settings Defaults Security Settings DefaultsFirmware Files Firmware UpgradesUsing Tftp Graphical User Interface Obtaining Firmware Reloading FirmwareTo recover firmware Using Tftp Command Line InterfaceFirmware Upgrades To enter Monitor Mode locally Monitor ModeEntering Monitor Mode Using the Serial Port Entering Monitor Mode Using the Network PortG0, G1, ....,Ge, Gf Monitor Mode CommandsMonitor Mode Commands Command Command Name FunctionResponse Meaning Command Response CodesTable A-2 Status LED Appendix a Troubleshooting and Contact InfoLEDs Status LEDProblems and Error Messages Serial LEDsRJ45 Ethernet LED Using DeviceInstaller Serial Settings on page 29 or Technical Support United StatesEurope, Middle East and Africa Serial Port Pinouts Appendix B Connections and PinoutsTable B-6 Ethernet RJ45 Connector Pin-Outs Ethernet Connector PinoutsPower Jack Mini USB-B Appendix C Technical Specifications Table C-1 xDirect Technical SpecificationsCategory Description Appendix C Technical Specifications AutoIP Appendix D Alternative Ways to Assign an IP AddressTo assign a temporary IP address ARP and TelnetScientific Calculator Appendix E Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Conversion TableAppendix E Binary to Hexadecimal Conversions Electromagnetic Emissions SafetyAppendix F Compliance Manufacturer’s Name & AddressRoHS Notice Appendix F Compliance
Top Page Image Contents