Lantronix 900-653-R manual Appendix B Connections and Pinouts, Serial Port Pinouts

Page 72

Appendix B: Connections and Pinouts

The xDirect has a DB9F DCE connector, and an Ethernet 10/100 RJ45 interface. The xDirect can be powered via a mini USB-B jack with a provided 5 VDC power supply, or Ethernet PoE (hardware optional), or DB9F pin 9 and 5.

Figure B-1 Single Serial Port and Ethernet Port on xDirect

Serial Port Pinouts

The xDirect has one female DB9 DCE serial port that supports one of three pinouts depending on the model of your xDirect unit:

Figure B-2 DB9F in RS232 Mode (All Models)

Figure B-3 DB9F in RS422/485 (4-Wire) Mode (xDirect485 & PoE Models)

xDirect User Guide

Image 72

Contents User Guide Warranty Copyright & TrademarkContacts DisclaimerTable of Contents Using this GuideInstallation of xDirect Using DeviceInstallerConfiguration Using Web Manager Configuration Via Telnet or Serial Port Setup ModeSetup Mode Server Configuration Setup Mode Channel ConfigurationSetup Mode Advanced Settings Firmware UpgradesMonitor Mode Appendix a Troubleshooting and Contact Info Appendix B Connections and PinoutsAppendix E Binary to Hexadecimal Conversions Appendix F ComplianceList of Figures Serial Tunneling ExampleList of Tables Using this Guide Purpose and AudienceChapter Summary Additional Documentation Document DescriptionKey Features IntroductionApplications Introduction Additional Features Configuration MethodsProtocol Support Product Information Label Product LabelInstallation of xDirect Package ContentsInstalling the xDirect Required Information Hardware AddressIP Address Using DeviceInstaller Installing DeviceInstallerTo install DeviceInstaller Assigning an IP AddressAccessing the xDirect Using DeviceInstaller Viewing the Current ConfigurationTo view the units current settings XDirect Configuration in DeviceInstallerSupports Configurable Pins CommentsDevice Family TypeAssigning the IP Address Serial Port Login Next StepConfiguration Using Web Manager Accessing xDirect Using DeviceInstallerConfiguration Using Web Manager Network Configuration Network ModeAutomatic IP Address Configuration To assign an IP address automaticallyStatic IP Address Configuration Ethernet ConfigurationSelect Use the following IP configuration To assign an IP address manuallyServer Configuration To configure the xDirect device server settingsMonitor Mode @ Bootup CPU Performance ModeConfig Server Port Timeout msHost List Configuration To configure the host listRetry Timeout Retry CounterChannel 1 Configuration Serial SettingsTo configure the channel’s serial settings Enable Packing Baud RateData Bits ParityConnection Settings TCP To configure a channel’s TCP settingsAccept Incoming Password Required Modem ModeModem Escape Sequence Pass ThroughConnection Settings UDP To configure a channel’s UDP settingsDatagram Type Use BroadcastDevice Address Table Apply Settings Apply DefaultsConfiguration Via Telnet or Serial Port Setup Mode Accessing Setup ModeTelnet Connection To establish a Telnet connectionPassword Press Enter for Setup Mode Exiting Setup Mode Two options through which to exit setup modeSerial Port Connection Setup Mode Server Configuration Server Configuration OptionBootP/DHCP/AutoIP options IP AddressSet Gateway IP Address Netmask Number of Bits for Host PartSet DNS Server IP Address Standard IP Network NetmasksChange Telnet Configuration Password Dhcp NameSetup Mode Channel Configuration Channel 1 OptionBaudrate Interface Mode Interface Mode OptionsCommon Interface Mode Settings FlowConnect Mode Port NumberFlow Control Options Reserved Port NumbersConnect Mode Options Connect Mode OptionIncoming Connection Response Active StartupManual Connection Address Example Host List Option Hostlist C0.0.0.0/0Autostart Automatic ConnectionModem Mode To enable the hostlistDatagram Type Directed UDPModem Mode Messages Message MeaningSend the Escape Sequence +++ in Modem Mode 10 Modem Mode CommandsModem Mode Function Command Show IP Address after RingDisconnect Mode DisConnMode Auto Increment Source PortRemote IP Address Remote PortFlush Mode Buffer Flushing 11 Disconnect Mode Options12 Flush Mode Options Pack Control Packing IntervalTrailing Characters Send CharactersDisConnTime Inactivity Timeout Channel Port PasswordSend Characters Telnet Terminal TypeSetup Mode Advanced Settings Expert Settings OptionARP Cache Timeout In Seconds TCP Keepalive Time In SecondsSecurity Settings Option Disable Snmp Disable Telnet SetupSnmp Community Name Disable Tftp Firmware Update Disable Port 77FE HexDisable Web Server Disable Web SetupDefault Settings Option Enable Enhanced PasswordChannel 1 Configuration Defaults Expert Settings DefaultsSecurity Settings Defaults Setup Mode Advanced SettingsFirmware Upgrades Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware Firmware FilesUsing Tftp Command Line Interface To recover firmwareFirmware Upgrades Monitor Mode Entering Monitor Mode Using the Serial PortEntering Monitor Mode Using the Network Port To enter Monitor Mode locallyMonitor Mode Commands Monitor Mode CommandsCommand Command Name Function G0, G1, ....,Ge, GfCommand Response Codes Response MeaningAppendix a Troubleshooting and Contact Info LEDsStatus LED Table A-2 Status LEDProblems and Error Messages Serial LEDsRJ45 Ethernet LED Using DeviceInstaller Serial Settings on page 29 or Technical Support United StatesEurope, Middle East and Africa Appendix B Connections and Pinouts Serial Port PinoutsEthernet Connector Pinouts Table B-6 Ethernet RJ45 Connector Pin-OutsPower Jack Mini USB-B Appendix C Technical Specifications Table C-1 xDirect Technical SpecificationsCategory Description Appendix C Technical Specifications Appendix D Alternative Ways to Assign an IP Address AutoIPARP and Telnet To assign a temporary IP addressAppendix E Binary to Hexadecimal Conversions Converting Binary to HexadecimalConversion Table Scientific CalculatorAppendix E Binary to Hexadecimal Conversions Safety Appendix F ComplianceManufacturer’s Name & Address Electromagnetic EmissionsAppendix F Compliance RoHS Notice