Lantronix Hub manual Disclaimer & Revisions

Page 3

Disclaimer & Revisions

Operation of this equipment in a residential area is likely to cause interference in which case the user, at his or her own expense, will be required to take whatever measures may be required to correct the interference.

Attention: This product has been designed to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against such interference when operating in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with this guide, may cause harmful interference to radio communications.

Changes or modifications to this device not explicitly approved by Lantronix will void the user's authority to operate this device.

The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors that may appear in this guide.

ii

Image 3
Contents MSS User Guide Lantronix Corporate Headquarters Technical SupportSales Offices Disclaimer & Revisions Contents Configuration Using the MSS Compliance and Warranty Information Introduction to the MSS Family MSS Family FeaturesProtocols About The Documentation TermsMSS User Guide Introduction to the MSS Family Installation MSS-VIA InstallationComponents MSS-VIA LEDs MSS-VIA Rear PanelExample Wired Network Layout Installation ProcedureMSS User Guide Installation Pinging the MSS Humidity MSS-VIA SpecificationsPower power cube adaptor TemperatureMSS4 Components MSS4 InstallationMSS Connected to a Serial Device and Network MSS4 LEDsMSS User Guide Installation MSS4 Specifications 10 MSS100 Front Panel MSS100 Installation12 MSS Network Layout MSS100 LEDs13 MSS Connected to Serial Device and Ethernet 14 Pinging the MSS MSS100 SpecificationsPrivileged User Status Getting StartedFrom the Action menu, select Assign IP Address IP Address ConfigurationUsing EZWebCon Using a Web BrowserEntering ARP and Ping Unix Using ARP and PingUsing the Serial Console Using a DHCP, BOOTP, or Rarp ReplyWeb Browser Login and Configuration Incoming LoginsLogin Password Incoming TCP/IP LoginsTelnet Serial Port LoginsEZWebCon Login and Configuration RloginChanging the Login Password Remote Console LoginsIncoming LAT Logins Logout Outbound ConnectionsOverview ConfigurationRebooting the MSS Normal RebootProtocol Configuration Factory DefaultsTCP/IP Configuration Name Server Specifying a Gateway for MSS-VIA and MSS4Supported Mibs IP SecurityRouting and Encapsulation IPX NetWare ConfigurationConfiguring Snmp Snmp Trap SupportLoadhost Internal Network NumberServer Identification LAT ConfigurationService Groups Circuit TimerTwo-Wire Mode RS-485 Configuration22 Enabling Two-Wire RS-485 Mode for MSS4 Four-Wire ModeTermination TXDriveSerial Port Configuration Access ModeAutostart Serial Data 36 Configuring an Autostart Character for MSS-VIA and MSS4Character Size, Parity, and Stop Bits Baud RateFlow Control Modems and Modem SignalingSignal Checking Modem ControlDSRLogout DTRWait LogoutsConfiguration Preferred HostDedicated Host Region Enabling 802.11 NetworkingMAC Address Extended Service Set ID EssidNetwork Mode Setting the WEP Key and Index NumberChannel Formatting an ATA Flash Card Modem CardsEncrypted Traffic Outgoing Calls Incoming CallsUsing the MSS Incoming ConnectionsSocket Connections Interactive Connections Outbound ConnectionsTCP/IP Socket Connections Break Key and Local Switch Backward, Forward, and SwitchesSession Control Show Status DisplaysDisconnect and Resume Session LimitsSerial Tunnel UDP Configuration TCP ConfigurationEnabling Multihost Mode Multihost ModeModem Emulation Mode Adding HostsRemoving Hosts 17. Enabling Modem Mode for MSS100 Modem Mode CommandsSequential Hostlist Mode Wiring RequirementsCOM Port Redirector Troubleshooting Power-up TroubleshootingPower-up Problems and Error Messages Bootp Troubleshooting Dhcp TroubleshootingBootp Troubleshooting Dhcp TroubleshootingRarp Troubleshooting Rarp TroubleshootingTftp Troubleshooting Modem Configuration ChecklistEntering Commands at the Boot Prompt Change Bootp Enabled, DisabledInit Change Loadhost ipaddress Change Dhcp Enabled, DisabledChange Hardware Change Ipaddress ipaddressTechnical Support Europe, Middle East, and Africa Technical SupportPinouts Ethernet ConnectorMSS VIA Connectors Serial ConnectorsMSS4 Connectors RS-232 DB9 ConnectorRS-485 DB9 Connectors MSS100 Connectors DB25 ConnectorRS-232 DB9 Connectors Modem Wiring DSR Data Signal Ready versus CD Carrier DetectDTR Data Terminal Ready Via the Web Via FTP Updating SoftwareObtaining Software Reloading SoftwareFTP Troubleshooting Flash ROM Updates Flash ROM TroubleshootingNetWare MSS User Guide Updating Software Compliance Information Compliance and Warranty InformationWarranty