Lantronix Hub manual Internal Network Number, Loadhost

Page 39

MSS User Guide

4: Configuration

The MSS can be restricted to a single frame format, in which case it will not do internal routing. Two commands control this behavior: Change NetWare Routing and Change NetWare Encapsulation.

‹Change NetWare Routing enables or disables the use of the internal network number. By default, internal routing is enabled.

Note: If two or more frame types are enabled, internal routing must be enabled. To see which frame types are enabled, enter the Show NetWare command.

‹Change NetWare Encapsulation controls which of the frame types are used. The choices are Ether_II, Native, 802_2, and SNAP, which provide for Ethernet v2, 802.3 Native mode, 802.2, and 802.2 SNAP encapsulation types.

Figure 4-14 displays an example routing and encapsulation configuration. The 802.3 Native mode and 802.2 SNAP frame types are enabled, while Ethernet v2 and 802.2 are disabled. Because more than one frame type is enabled, internal routing must also be enabled.

Figure 4-14: Enabling Selected Frame Types

Local>> CHANGE NETWARE ENCAPSULATION NATIVE ENABLED

Local>> CHANGE NETWARE ENCAPSULATION SNAP ENABLED

Local>> CHANGE NETWARE ENCAPSULATION ETHER_2 DISABLED

Local>> CHANGE NETWARE ENCAPSULATION 802_2 DISABLED

Local>> CHANGE NETWARE ROUTING ENABLED

Internal Network Number

When internal routing is enabled, the MSS needs an internal network number that is unique on the network. When addressing IPX packets to a fileserver, devices use the fileserver’s internal network number as the destination address.

The internal network number for the MSS is a four-byte number that defaults to the last four bytes of the unit’s Ethernet address (for example, a3001234). It is unlikely that this number will need to be changed.

Note: If you do change the internal network number, reboot the MSS.

Loadhost

A loadhost is a NetWare fileserver from which the MSS will try to load code when the Initialize Reload command is entered. If the software loadfile or loadhost address changes, you will have to change the configured parameters for the next reboot. For the following example, the loadhost is “phred” and the name of the loadfile is “MSS100.SYS”.

Figure 4-15: Changing the NetWare Loadhost

Local_2>> CHANGE NETWARE LOADHOST phred

Local_2>> CHANGE SOFTWARE sys:login/MSS100.SYS

4-6

Image 39
Contents MSS User Guide Lantronix Corporate Headquarters Technical SupportSales Offices Disclaimer & Revisions Contents Configuration Using the MSS Compliance and Warranty Information Introduction to the MSS Family MSS Family FeaturesProtocols About The Documentation TermsMSS User Guide Introduction to the MSS Family Installation MSS-VIA InstallationComponents MSS-VIA LEDs MSS-VIA Rear PanelExample Wired Network Layout Installation ProcedureMSS User Guide Installation Pinging the MSS Humidity MSS-VIA SpecificationsPower power cube adaptor TemperatureMSS4 Components MSS4 InstallationMSS Connected to a Serial Device and Network MSS4 LEDsMSS User Guide Installation MSS4 Specifications 10 MSS100 Front Panel MSS100 Installation12 MSS Network Layout MSS100 LEDs13 MSS Connected to Serial Device and Ethernet 14 Pinging the MSS MSS100 SpecificationsPrivileged User Status Getting StartedFrom the Action menu, select Assign IP Address IP Address ConfigurationUsing EZWebCon Using a Web BrowserEntering ARP and Ping Unix Using ARP and PingUsing the Serial Console Using a DHCP, BOOTP, or Rarp ReplyWeb Browser Login and Configuration Incoming LoginsLogin Password Incoming TCP/IP LoginsTelnet Serial Port LoginsEZWebCon Login and Configuration RloginChanging the Login Password Remote Console LoginsIncoming LAT Logins Logout Outbound ConnectionsOverview ConfigurationRebooting the MSS Normal RebootProtocol Configuration Factory DefaultsTCP/IP Configuration Name Server Specifying a Gateway for MSS-VIA and MSS4Supported Mibs IP SecurityRouting and Encapsulation IPX NetWare ConfigurationConfiguring Snmp Snmp Trap SupportLoadhost Internal Network NumberServer Identification LAT ConfigurationService Groups Circuit TimerTwo-Wire Mode RS-485 Configuration22 Enabling Two-Wire RS-485 Mode for MSS4 Four-Wire ModeTermination TXDriveSerial Port Configuration Access ModeAutostart Serial Data 36 Configuring an Autostart Character for MSS-VIA and MSS4Character Size, Parity, and Stop Bits Baud RateFlow Control Modems and Modem SignalingSignal Checking Modem ControlDSRLogout DTRWait LogoutsConfiguration Preferred HostDedicated Host Region Enabling 802.11 NetworkingMAC Address Extended Service Set ID EssidNetwork Mode Setting the WEP Key and Index NumberChannel Formatting an ATA Flash Card Modem CardsEncrypted Traffic Outgoing Calls Incoming CallsUsing the MSS Incoming ConnectionsSocket Connections Interactive Connections Outbound ConnectionsTCP/IP Socket Connections Break Key and Local Switch Backward, Forward, and SwitchesSession Control Show Status DisplaysDisconnect and Resume Session LimitsSerial Tunnel UDP Configuration TCP ConfigurationEnabling Multihost Mode Multihost ModeModem Emulation Mode Adding HostsRemoving Hosts 17. Enabling Modem Mode for MSS100 Modem Mode CommandsSequential Hostlist Mode Wiring RequirementsCOM Port Redirector Troubleshooting Power-up TroubleshootingPower-up Problems and Error Messages Bootp Troubleshooting Dhcp TroubleshootingBootp Troubleshooting Dhcp TroubleshootingRarp Troubleshooting Rarp TroubleshootingTftp Troubleshooting Modem Configuration ChecklistEntering Commands at the Boot Prompt Change Bootp Enabled, DisabledInit Change Loadhost ipaddress Change Dhcp Enabled, DisabledChange Hardware Change Ipaddress ipaddressTechnical Support Europe, Middle East, and Africa Technical SupportPinouts Ethernet ConnectorMSS VIA Connectors Serial ConnectorsMSS4 Connectors RS-232 DB9 ConnectorRS-485 DB9 Connectors MSS100 Connectors DB25 ConnectorRS-232 DB9 Connectors Modem Wiring DSR Data Signal Ready versus CD Carrier DetectDTR Data Terminal Ready Via the Web Via FTP Updating SoftwareObtaining Software Reloading SoftwareFTP Troubleshooting Flash ROM Updates Flash ROM TroubleshootingNetWare MSS User Guide Updating Software Compliance Information Compliance and Warranty InformationWarranty