Lantronix Hub manual Session Control, Break Key and Local Switch, Backward, Forward, and Switches

Page 58

MSS User Guide

5: Using the MSS

Note: Because Rlogin can bypass the normal password/login sequence and is therefore a potential security problem, it may be disabled on some hosts. It is disabled by default on the MSS.

Session Control

When a user makes a connection to a service on the network (via Telnet or Rlogin), a session is created. A user can have several connections to various services at once, although only one is displayed on the screen at a time. Each separate connection is a session. The following section explains commands used to manipulate these sessions.

Break Key and Local Switch

The Break key allows users to leave an active session and return to the MSS Local> prompt without disconnecting sessions. By default, the MSS handles the Break key locally. Users can change whether the Break key is processed by the MSS (Local), processed by the remote host (Remote), or ignored (None) using the Change Port Break command.

Figure 5-4: Changing the Break Key for MSS-VIA and MSS4

Local>> CHANGE PORT 1 BREAK REMOTE

Figure 5-5: Changing the Break Key for MSS100

Local>> CHANGE BREAK REMOTE

If your terminal does not have a Break key, you can configure a local switch key.

Figure 5-6: Defining a Local Switch for MSS-VIA and MSS4

Local>> CHANGE PORT 1 LOCAL SWITCH ^L

Figure 5-7: Defining a Local Switch for MSS100

Local>> CHANGE LOCAL SWITCH ^L

Backward, Forward, and Switches

The Backward and Forward commands, when entered at the Local> prompt, allow users to navigate through current sessions.

A user's open sessions can be thought of as a list from the earliest to the most recently created. Forward refers to a more recent connection, while Backward refers to a session started earlier. The list is also circular; going forward from the most recently created session takes you to the earliest session, and going backward from the earliest session resumes the most recent session. For example, user Bob connects to host Thor. He then breaks to local mode and connects to host Duff. After working, he breaks and connects to host Conan. His session list, shown with the Show Session command, would be:

Thor

Duff Conan

Conan is the current session, meaning the session to which the user is currently connected or the last session the user was in before entering local mode. If Bob presses the backward key while working in Conan, he will resume his session on Duff. If he presses the forward key while working in Conan, he will move to his session on Thor.

5-3

Image 58
Contents MSS User Guide Technical Support Lantronix Corporate HeadquartersSales Offices Disclaimer & Revisions Contents Configuration Using the MSS Compliance and Warranty Information MSS Family Features Introduction to the MSS FamilyProtocols Terms About The DocumentationMSS User Guide Introduction to the MSS Family MSS-VIA Installation InstallationComponents MSS-VIA Rear Panel MSS-VIA LEDsInstallation Procedure Example Wired Network LayoutMSS User Guide Installation Pinging the MSS Temperature MSS-VIA SpecificationsPower power cube adaptor HumidityMSS4 Installation MSS4 ComponentsMSS4 LEDs MSS Connected to a Serial Device and NetworkMSS User Guide Installation MSS4 Specifications MSS100 Installation 10 MSS100 Front PanelMSS100 LEDs 12 MSS Network Layout13 MSS Connected to Serial Device and Ethernet MSS100 Specifications 14 Pinging the MSSGetting Started Privileged User StatusUsing a Web Browser IP Address ConfigurationUsing EZWebCon From the Action menu, select Assign IP AddressUsing ARP and Ping Entering ARP and Ping UnixUsing a DHCP, BOOTP, or Rarp Reply Using the Serial ConsoleIncoming TCP/IP Logins Incoming LoginsLogin Password Web Browser Login and ConfigurationRlogin Serial Port LoginsEZWebCon Login and Configuration TelnetRemote Console Logins Changing the Login PasswordIncoming LAT Logins Outbound Connections LogoutNormal Reboot ConfigurationRebooting the MSS OverviewFactory Defaults Protocol ConfigurationTCP/IP Configuration Specifying a Gateway for MSS-VIA and MSS4 Name ServerIP Security Supported MibsSnmp Trap Support IPX NetWare ConfigurationConfiguring Snmp Routing and EncapsulationInternal Network Number LoadhostCircuit Timer LAT ConfigurationService Groups Server IdentificationRS-485 Configuration Two-Wire ModeFour-Wire Mode 22 Enabling Two-Wire RS-485 Mode for MSS4TXDrive TerminationAccess Mode Serial Port ConfigurationAutostart 36 Configuring an Autostart Character for MSS-VIA and MSS4 Serial DataBaud Rate Character Size, Parity, and Stop BitsModems and Modem Signaling Flow ControlModem Control Signal CheckingDSRLogout Logouts DTRWaitPreferred Host ConfigurationDedicated Host Enabling 802.11 Networking RegionExtended Service Set ID Essid MAC AddressSetting the WEP Key and Index Number Network ModeChannel Modem Cards Formatting an ATA Flash CardEncrypted Traffic Incoming Calls Outgoing CallsIncoming Connections Using the MSSSocket Connections Outbound Connections Interactive ConnectionsTCP/IP Socket Connections Backward, Forward, and Switches Break Key and Local SwitchSession Control Session Limits Status DisplaysDisconnect and Resume ShowSerial Tunnel TCP Configuration UDP ConfigurationMultihost Mode Enabling Multihost ModeAdding Hosts Modem Emulation ModeRemoving Hosts Modem Mode Commands 17. Enabling Modem Mode for MSS100Wiring Requirements Sequential Hostlist ModeCOM Port Redirector Power-up Troubleshooting TroubleshootingPower-up Problems and Error Messages Dhcp Troubleshooting Dhcp TroubleshootingBootp Troubleshooting Bootp TroubleshootingModem Configuration Checklist Rarp TroubleshootingTftp Troubleshooting Rarp TroubleshootingChange Bootp Enabled, Disabled Entering Commands at the Boot PromptInit Change Ipaddress ipaddress Change Dhcp Enabled, DisabledChange Hardware Change Loadhost ipaddressTechnical Support Technical Support Europe, Middle East, and AfricaSerial Connectors Ethernet ConnectorMSS VIA Connectors PinoutsRS-232 DB9 Connector MSS4 ConnectorsRS-485 DB9 Connectors DB25 Connector MSS100 ConnectorsRS-232 DB9 Connectors DSR Data Signal Ready versus CD Carrier Detect Modem WiringDTR Data Terminal Ready Reloading Software Updating SoftwareObtaining Software Via the Web Via FTPFTP Flash ROM Troubleshooting Troubleshooting Flash ROM UpdatesNetWare MSS User Guide Updating Software Compliance and Warranty Information Compliance InformationWarranty