Lantronix Hub manual Using the MSS

Page 6

Extended Service Set ID (ESSID)__________________________________4-18

Network Mode_________________________________________________4-18

Channel______________________________________________________4-18

WEP ________________________________________________________4-18

Formatting an ATA Flash Card ____________________________________4-18

Modem Cards _________________________________________________4-18

5:Using the MSS _____________________________________________ 5-18

Incoming Connections ______________________________________________5-18 Socket Connections ____________________________________________5-18 Interactive Connections _____________________________________________5-18 Outbound Connections __________________________________________5-18 Session Control________________________________________________5-18 Status Displays ________________________________________________5-18 Serial Tunnel _____________________________________________________5-18 TCP Configuration______________________________________________5-18 UDP Configuration _____________________________________________5-18 Multihost Mode ___________________________________________________5-18 Enabling Multihost Mode_________________________________________5-18 Adding Hosts__________________________________________________5-18 Removing Hosts _______________________________________________5-18 Modem Emulation Mode ____________________________________________5-18 Modem Mode Commands________________________________________5-18 Wiring Requirements____________________________________________5-18 Sequential Hostlist Mode____________________________________________5-18 COM Port Redirector _______________________________________________5-18

6:Troubleshooting____________________________________________ 6-18

Power-up Troubleshooting __________________________________________6-18 DHCP Troubleshooting _____________________________________________6-18 BOOTP Troubleshooting ____________________________________________6-18 RARP Troubleshooting _____________________________________________6-18 TFTP Troubleshooting______________________________________________6-18 Modem Configuration Checklist_______________________________________6-18 Entering Commands at the Boot Prompt________________________________6-18 Technical Support _________________________________________________6-18

7:Pinouts ___________________________________________________ 7-18

Ethernet Connector ________________________________________________7-18

v

Page 5 Page 7
Image 6
Page 5 Page 7
Contents MSS User Guide Lantronix Corporate Headquarters Technical SupportSales Offices Disclaimer & Revisions Contents Configuration Using the MSS Compliance and Warranty Information MSS Family Features Introduction to the MSS FamilyProtocols Terms About The DocumentationMSS User Guide Introduction to the MSS Family Installation MSS-VIA InstallationComponents MSS-VIA Rear Panel MSS-VIA LEDsInstallation Procedure Example Wired Network LayoutMSS User Guide Installation Pinging the MSS Temperature MSS-VIA SpecificationsPower power cube adaptor HumidityMSS4 Installation MSS4 ComponentsMSS4 LEDs MSS Connected to a Serial Device and NetworkMSS User Guide Installation MSS4 Specifications MSS100 Installation 10 MSS100 Front PanelMSS100 LEDs 12 MSS Network Layout13 MSS Connected to Serial Device and Ethernet MSS100 Specifications 14 Pinging the MSSGetting Started Privileged User StatusUsing a Web Browser IP Address ConfigurationUsing EZWebCon From the Action menu, select Assign IP AddressUsing ARP and Ping Entering ARP and Ping UnixUsing a DHCP, BOOTP, or Rarp Reply Using the Serial ConsoleIncoming TCP/IP Logins Incoming LoginsLogin Password Web Browser Login and ConfigurationRlogin Serial Port LoginsEZWebCon Login and Configuration TelnetChanging the Login Password Remote Console LoginsIncoming LAT Logins Outbound Connections LogoutNormal Reboot ConfigurationRebooting the MSS OverviewProtocol Configuration Factory DefaultsTCP/IP Configuration Specifying a Gateway for MSS-VIA and MSS4 Name ServerIP Security Supported MibsSnmp Trap Support IPX NetWare ConfigurationConfiguring Snmp Routing and EncapsulationInternal Network Number LoadhostCircuit Timer LAT ConfigurationService Groups Server IdentificationRS-485 Configuration Two-Wire ModeFour-Wire Mode 22 Enabling Two-Wire RS-485 Mode for MSS4TXDrive TerminationSerial Port Configuration Access ModeAutostart 36 Configuring an Autostart Character for MSS-VIA and MSS4 Serial DataBaud Rate Character Size, Parity, and Stop BitsModems and Modem Signaling Flow ControlSignal Checking Modem ControlDSRLogout Logouts DTRWaitConfiguration Preferred HostDedicated Host Enabling 802.11 Networking RegionExtended Service Set ID Essid MAC AddressNetwork Mode Setting the WEP Key and Index NumberChannel Formatting an ATA Flash Card Modem CardsEncrypted Traffic Incoming Calls Outgoing CallsUsing the MSS Incoming ConnectionsSocket Connections Interactive Connections Outbound ConnectionsTCP/IP Socket Connections Break Key and Local Switch Backward, Forward, and SwitchesSession Control Session Limits Status DisplaysDisconnect and Resume ShowSerial Tunnel TCP Configuration UDP ConfigurationMultihost Mode Enabling Multihost ModeModem Emulation Mode Adding HostsRemoving Hosts Modem Mode Commands 17. Enabling Modem Mode for MSS100Sequential Hostlist Mode Wiring RequirementsCOM Port Redirector Troubleshooting Power-up TroubleshootingPower-up Problems and Error Messages Dhcp Troubleshooting Dhcp TroubleshootingBootp Troubleshooting Bootp TroubleshootingModem Configuration Checklist Rarp TroubleshootingTftp Troubleshooting Rarp TroubleshootingEntering Commands at the Boot Prompt Change Bootp Enabled, DisabledInit Change Ipaddress ipaddress Change Dhcp Enabled, DisabledChange Hardware Change Loadhost ipaddressTechnical Support Technical Support Europe, Middle East, and AfricaSerial Connectors Ethernet ConnectorMSS VIA Connectors PinoutsMSS4 Connectors RS-232 DB9 ConnectorRS-485 DB9 Connectors MSS100 Connectors DB25 ConnectorRS-232 DB9 Connectors Modem Wiring DSR Data Signal Ready versus CD Carrier DetectDTR Data Terminal Ready Reloading Software Updating SoftwareObtaining Software Via the Web Via FTPFTP Troubleshooting Flash ROM Updates Flash ROM TroubleshootingNetWare MSS User Guide Updating Software Compliance and Warranty Information Compliance InformationWarranty
Top Page Image Contents