Intellinet Network Solutions 524780 user manual Vpi, Vci

Page 38

ParameterDescription

VPI

VPI is a virtual path that determines the way an ATM cell

 

should be routed. The VPI is an 8-bit (in UNI) or 12-bit (in

 

NNI) number that is included in the header of an ATM

 

cell. The valid range for the VPI is 0 to 255. Enter the VPI

 

assigned by the ISP.

VCI

VCI is the label given to an ATM VC to identify it and

 

determine its destination. The VCI is a 16-bit number that

 

is included in the header of an ATM cell. The valid VCI

 

range is 32 to 65535. Enter the VCI assigned by the ISP.

Encapsulation

Check with your ISP for the method of multiplexing.

Channel Mode

There are five kinds of channel modes you can select for

 

an ADSL connection. Check with your ISP for the method

 

of the ADSL connection.

Enable NAPT

Enable or disable NAPT, an Internet standard that

 

enables a local-area network (LAN) to use one set of IP

 

addresses for internal traffic and a second set of

 

addresses for external traffic. When NAPT is enabled,

 

the router will help to make all necessary IP address

 

translations for the PC connected to the router to access

 

the Internet.

Admin Status

Enable or disable the PVC channel setting.

User Name

Enter the username exactly as your ISP assigned it.

Password

Enter the password that your ISP has assigned to you.

Type

Continuous – The connection will be kept always on. If

 

the connection is interrupted, the router will re-connect

 

automatically.

 

Connect on Demand – Only connects when you want to

 

surf the Internet. “Idle Time” is set to stop the connection

 

when the network traffic is not sending or receiving after

 

an idle time.

 

Manual – After you have selected this option, go to the

 

Status screen and click “Connect.” The router will

 

connect to the ISP. If you want to stop the connection,

 

click “Disconnect.”

32

Image 38
Contents Wireless 300N ADSL2+ Federal Communications Commission Interference Statement FCC PartFCC Caution Safety TTE Compliance StatementContents Troubleshooting Glossary Specifications Introduction Package Contents Minimum RequirementsON/OFF HardwareRear Panel AdslFront Panel Status DescriptionInstallation Setup Wizard Getting StartedPage Page Automatically Set the ISP Page Page Manually Set the ISP Page Page Page Page IP Address Setting Windows VistaWindows XP Windows Page Web Management Configuration General Setup Section Quick Setup Page System Time ZonePassword Settings Remote Management LAN WANMIB SnmpSnmp Channel Config 2 WANRFC1483 MER VPI VCIShould be routed ATM Setting SCR PCRCdvt MBSAdsl Setting 2.4 DNS Ddns 2.6 RIP ParameterDescription 3 LAN 192.168.2.1 Dhcp Mode Dhcp RelayDhcp Server Parameter Description ARP Table BridgingWireless Basic SettingsSsid Advanced Settings ParameterDescription Auto is the default authentication algorithm. It will Transmit the network name Ssid into open air at regular Security WPA2 AES for data encryption. The actual selection Access Control 4.5 WPS Parameter Description 5 QoS ParameterDescription NAT Network Address Translations TOSPort Forwarding Port Mapping Parameter Description Upnp Igmp Proxy Firewall 7.1 IP/Port FilteringListed in the table from connecting to the Internet MAC Filtering Page URL Blocking FqdnDomain Blocking Routing Configuration Page ACL Configuration 7.7 DMZ Status Interface Adsl Configuration Tools ToolsFirmware Upgrade PingATM Loopback Diagnostic Test RebootTroubleshooting Steps Corrective ActionPage Forget my login username and/or password Initialization of the Adsl connection failed 10Base-T Default Gateway RouterGlossary BridgeEthernet Idle TimeoutDNS Server IP Address ISP Gateway AddressMAC Address PortProtocol PPPoA RFCPPPoE RFC RFCWeb-based Management Graphical User Interface GUI RouterSubnet Mask General SpecificationsStandards WPA Radius WirelessWPA Tkip WPA2 AES LEDs PowerPackage Contents EnvironmentalEspañol EnglishDeutsch FrançaisItaliano PolskiWarranty Information