Juniper Networks manual 5000-2XGE SPM, Part Number Description Distance Fiber Type

Page 19

NetScreen-5000 Modules

The 5000-2XGE SPM

The 5000-2XGE SPM provides two 10-Gigabit mini-GBIC Ethernet ports using hot-swappable transceivers. The 5000-2XGE SPM delivers up to 10 Gbps of firewall and up to 5 Gbps of VPN capacity. This SPM cannot be mixed with the 5000-8G or 5000- 2G24FE SPMs.

(For details on connecting or removing a mini-GBIC transceiver and connecting and disconnecting a Gigabit Ethernet cable, see Chapter 4, Servicing the Device.)

The 5000-2XGE SPM provides port Link and Activity LEDs in addition to Power and Status LEDs.

Power LED Link LED

Two 10-Gigabit mini-GBIC Ports



Status LED		Transmit/
		Receive LED

Note: The 5000-2XGE SPM can only be managed by the 5000-M2 management module.

The following table shows the transceivers that are available with the 5000-2XGE SPM.

Part Number	Description	Distance	Fiber Type

NS-SYS-GBIC-MXSR	Transceiver, 300m 10 G, XFP	Short Reach	Multi-Mode Fiber

NS-SYS-GBIC-MXLR	Transceiver, 10km 10 G, XFP	Long Reach	Single-Mode Fiber

NS-SYS-GBIC-MXER	Transceiver, 40km 10 G, XFP	Extended Reach	Single-Mode Fiber

NetScreen-5000 Series

11

Image 19

Contents NETSCREEN-5000 Series Copyright Notice Table of Contents Servicing the Device IX-I Table of Contents Guide Organization PrefaceJuniper Networks Netscreen Publications Command Line Interface CLI ConventionsOverview1 NetScreen-5400 NetScreen-5200NETSCREEN-5000 Series NetScreen-5400 Power Recommendations NetScreen-5200 Power RecommendationsPower Supplies AC Power Supply DC Power SupplyNETSCREEN-5000 Modules FAN Modules5000-M Management Module Management Modules5000-M2 Management Module 5000-8G SPM Secure Port Modules5000-2G24FE SPM 5000-8G2 SPM Part Number Description Distance Fiber Type 5000-2XGE SPMOverview User’s Guide Installing the Device Equipment Rack Installation Guidelines General Installation GuidelinesMounting the NETSCREEN-5000 Series NetScreen-5200 Front and Rear MountNetScreen-5400 Front Mount NetScreen-5200 Mid-MountInstalling and Wiring a DC Power Supply Installing and Connecting the AC Power Supply48V COMThumbscrew Power Establishing AN HA Connection Connecting the NETSCREEN-5000 Series to a Router or SwitchInstalling the Device User’s Guide Configuring the Device Route Mode Transparent ModeOperational Modes NETSCREEN-5000 Interfaces NetScreen-5200 InterfacesNetScreen-5400 Interfaces Configurable InterfacesEstablishing a Terminal Emulator Connection Performing Initial Connection and ConfigurationUpgrading the Firmware During the Boot Process Setting the IP Address of the Management Interface Changing Your Admin Name and PasswordSetting Port and Interface IP Addresses Viewing Current Interface SettingsSetting the IP Address for the Untrust Zone Interface Setting the IP Address for the Trust Zone InterfaceConfiguring the Device for Telnet and Webui Sessions Starting a Console Session Using TelnetAllowing Outbound Traffic Establishing a GUI Management Session Starting a Console Session Using DialupHttp//10.100.2.183 Configuring the Chassis AlarmConfiguring Aggregate Interfaces Configuring Jumbo FramesFollowing CLI command unset admin device-reset Using CLI Commands to Reset the DevicePress the y key Following message appears Servicing the Device Removing and Reseating Modules Replacing a DC Power SupplyReplacing the FAN Module Replacing AN AC Power SupplyNetScreen-5200 Fan Module Remove the fan tray See NetScreen-5200 Fan Module on NetScreen-5200 Fan Tray FilterNetScreen-5400 Fan Module Replacing the Fan Module Remove the fan tray See NetScreen-5400 Fan Module on NetScreen-5400 Fan Tray FilterRemoving and Installing a MINI-GBIC Transceiver Connecting and Disconnecting Gigabit Ethernet CablesServicing the Device User’s Guide Specifications Environmental Electrical SpecificationNETSCREEN-5200 Attributes NETSCREEN-5400 AttributesEMI Certifications Safety CertificationsConnectors Nebs CertificationsAppendix a Specifications Port Descriptions and LED Status B MGT Module Port DescriptionsFollowing table details the ports on the 5000-8G2 SPM Module LED DescriptionsStatus LED States Interpreting Status LEDs for the Management ModulesInterpreting Ethernet Port Status LEDs for All Modules Interpreting Status LEDs for the Secure Port ModuleSingle SPM Installed Interpreting Power Supply LED Status for the NetScreen-5200Interpreting Power Supply LED Status for the NetScreen-5400 Power Supply LedsFAN LED Viii Index IX-II