Juniper Networks 5000 Changing Your Admin Name and Password, Viewing Current Interface Settings

Page 35

Performing Initial Connection and Configuration

Changing Your Admin Name and Password

Because all NetScreen products use the same admin name and password (netscreen), it is highly advisable to change your admin name and password immediately. Enter the following commands:

set admin name name_str set admin password pswd_str save

For information on creating different levels of administrators, see the NetScreen Concepts & Examples ScreenOS Reference Guide.

Setting Port and Interface IP Addresses

Through the CLI, you can execute commands that set IP address and subnet mask values for most of the physical interfaces.

Viewing Current Interface Settings

To begin the configuration process, it is advisable to view existing port settings by executing the following command:

get interface

This command displays current port names, IP addresses, MAC addresses, and other useful information.

Setting the IP Address of the Management Interface

The default IP address and subnet mask settings for the MGT interface are 192.168.1.1 and 255.255.255.0, respectively. To access the MGT interface, you must change the IP address and subnet mask of the MGT interface to match your current network. NetScreen recommends using the MGT interface exclusively for out of band management.

Note: The MGT interface is on the 5000-M or 5000-M2 management modules, which are always in slot 1.

To set the IP address of the MGT interface:

1.Choose an unused IP address within the current address range of your Local Area Network.

2.Set the MGT interface to this unused IP address by executing the following command:

set interface mgt ip ip_addr/mask

NetScreen-5000 Series

27

Image 35
Contents NETSCREEN-5000 Series Copyright Notice Table of Contents Servicing the Device IX-I Table of Contents Guide Organization PrefaceJuniper Networks Netscreen Publications Command Line Interface CLI ConventionsOverview1 NETSCREEN-5000 Series NetScreen-5200NetScreen-5400 Power Supplies NetScreen-5200 Power RecommendationsNetScreen-5400 Power Recommendations AC Power Supply DC Power SupplyNETSCREEN-5000 Modules FAN Modules5000-M Management Module Management Modules5000-M2 Management Module 5000-8G SPM Secure Port Modules5000-2G24FE SPM 5000-8G2 SPM Part Number Description Distance Fiber Type 5000-2XGE SPMOverview User’s Guide Installing the Device Equipment Rack Installation Guidelines General Installation GuidelinesMounting the NETSCREEN-5000 Series NetScreen-5200 Front and Rear MountNetScreen-5400 Front Mount NetScreen-5200 Mid-MountInstalling and Wiring a DC Power Supply Installing and Connecting the AC Power Supply48V COMThumbscrew Power Establishing AN HA Connection Connecting the NETSCREEN-5000 Series to a Router or SwitchInstalling the Device User’s Guide Configuring the Device Operational Modes Transparent ModeRoute Mode NETSCREEN-5000 Interfaces NetScreen-5200 InterfacesNetScreen-5400 Interfaces Configurable InterfacesEstablishing a Terminal Emulator Connection Performing Initial Connection and ConfigurationUpgrading the Firmware During the Boot Process Setting the IP Address of the Management Interface Changing Your Admin Name and PasswordSetting Port and Interface IP Addresses Viewing Current Interface SettingsSetting the IP Address for the Untrust Zone Interface Setting the IP Address for the Trust Zone InterfaceAllowing Outbound Traffic Starting a Console Session Using TelnetConfiguring the Device for Telnet and Webui Sessions Establishing a GUI Management Session Starting a Console Session Using DialupHttp//10.100.2.183 Configuring the Chassis AlarmConfiguring Aggregate Interfaces Configuring Jumbo FramesFollowing CLI command unset admin device-reset Using CLI Commands to Reset the DevicePress the y key Following message appears Servicing the Device Removing and Reseating Modules Replacing a DC Power SupplyReplacing the FAN Module Replacing AN AC Power SupplyNetScreen-5200 Fan Module Remove the fan tray See NetScreen-5200 Fan Module on NetScreen-5200 Fan Tray FilterNetScreen-5400 Fan Module Replacing the Fan Module Remove the fan tray See NetScreen-5400 Fan Module on NetScreen-5400 Fan Tray FilterRemoving and Installing a MINI-GBIC Transceiver Connecting and Disconnecting Gigabit Ethernet CablesServicing the Device User’s Guide Specifications Environmental Electrical SpecificationNETSCREEN-5200 Attributes NETSCREEN-5400 AttributesEMI Certifications Safety CertificationsConnectors Nebs CertificationsAppendix a Specifications Port Descriptions and LED Status B MGT Module Port DescriptionsFollowing table details the ports on the 5000-8G2 SPM Module LED DescriptionsStatus LED States Interpreting Status LEDs for the Management ModulesInterpreting Ethernet Port Status LEDs for All Modules Interpreting Status LEDs for the Secure Port ModuleSingle SPM Installed Interpreting Power Supply LED Status for the NetScreen-5200Interpreting Power Supply LED Status for the NetScreen-5400 Power Supply LedsFAN LED Viii Index IX-II