Juniper Networks 5000 manual Press the y key Following message appears

Page 42

Chapter 3 Configuring the Device

3.Press the y key.

The following message appears:

!! Reconfirm Lost Password Reset !! If you continue, the entire configuration of the device will be erased. In addition, a permanent counter will be incremented to signify that this device has been reset. This is your last chance to cancel this command. If you proceed, the device will return to factory default configuration, which is: System IP: 192.168.1.1; username: netscreen; password: netscreen. Would you like to continue? y/[n]

4.Press the y key to reset the device.

You can now login in using netscreen as the default admin name and password.

34	User’s Guide

Image 42

Contents NETSCREEN-5000 Series Copyright Notice Table of Contents Servicing the Device IX-I Table of Contents Preface Guide OrganizationCommand Line Interface CLI Conventions Juniper Networks Netscreen PublicationsOverview1 NetScreen-5200 NetScreen-5400NETSCREEN-5000 Series NetScreen-5200 Power Recommendations NetScreen-5400 Power RecommendationsPower Supplies DC Power Supply AC Power SupplyFAN Modules NETSCREEN-5000 ModulesManagement Modules 5000-M Management Module5000-M2 Management Module Secure Port Modules 5000-8G SPM5000-2G24FE SPM 5000-8G2 SPM 5000-2XGE SPM Part Number Description Distance Fiber TypeOverview User’s Guide Installing the Device General Installation Guidelines Equipment Rack Installation GuidelinesNetScreen-5200 Front and Rear Mount Mounting the NETSCREEN-5000 SeriesNetScreen-5200 Mid-Mount NetScreen-5400 Front MountInstalling and Connecting the AC Power Supply Installing and Wiring a DC Power Supply48V COMThumbscrew Power Connecting the NETSCREEN-5000 Series to a Router or Switch Establishing AN HA ConnectionInstalling the Device User’s Guide Configuring the Device Transparent Mode Route ModeOperational Modes NetScreen-5200 Interfaces NETSCREEN-5000 InterfacesConfigurable Interfaces NetScreen-5400 InterfacesPerforming Initial Connection and Configuration Establishing a Terminal Emulator ConnectionUpgrading the Firmware During the Boot Process Viewing Current Interface Settings Changing Your Admin Name and PasswordSetting Port and Interface IP Addresses Setting the IP Address of the Management InterfaceSetting the IP Address for the Trust Zone Interface Setting the IP Address for the Untrust Zone InterfaceStarting a Console Session Using Telnet Configuring the Device for Telnet and Webui SessionsAllowing Outbound Traffic Starting a Console Session Using Dialup Establishing a GUI Management SessionConfiguring the Chassis Alarm Http//10.100.2.183Configuring Jumbo Frames Configuring Aggregate InterfacesUsing CLI Commands to Reset the Device Following CLI command unset admin device-resetPress the y key Following message appears Servicing the Device Replacing a DC Power Supply Removing and Reseating ModulesReplacing AN AC Power Supply Replacing the FAN ModuleNetScreen-5200 Fan Module NetScreen-5200 Fan Tray Filter Remove the fan tray See NetScreen-5200 Fan Module onNetScreen-5400 Fan Module Replacing the Fan Module NetScreen-5400 Fan Tray Filter Remove the fan tray See NetScreen-5400 Fan Module onConnecting and Disconnecting Gigabit Ethernet Cables Removing and Installing a MINI-GBIC TransceiverServicing the Device User’s Guide Specifications NETSCREEN-5400 Attributes Electrical SpecificationNETSCREEN-5200 Attributes EnvironmentalNebs Certifications Safety CertificationsConnectors EMI CertificationsAppendix a Specifications Port Descriptions and LED Status B Module Port Descriptions MGTModule LED Descriptions Following table details the ports on the 5000-8G2 SPMInterpreting Status LEDs for the Management Modules Status LED StatesInterpreting Status LEDs for the Secure Port Module Interpreting Ethernet Port Status LEDs for All ModulesPower Supply Leds Interpreting Power Supply LED Status for the NetScreen-5200Interpreting Power Supply LED Status for the NetScreen-5400 Single SPM InstalledFAN LED Viii Index IX-II