Juniper Networks 5000 manual Interpreting Status LEDs for the Secure Port Module

Page 61

Interpreting Status LEDs for the Secure Port Module

The Status LEDs indicate whether the Secure Port Module is operating properly. The following table describes the status possibilities for each.

LED	LED Color	Meaning of the LED

POWER	green	Indicates the system is receiving power.
	off	Indicates the system is not receiving power.
	amber	Indicates the system has initially received power.

STATUS	blinking	Indicates the system is up and operational and that the power source is
	green	working properly.
	green	Indicates the system has a problem.
	off	Indicates the Secure Port Module is not operational.

Interpreting Ethernet Port Status LEDs for All Modules

The port Status LEDs indicate whether any of the ports on the modules are operating properly. The following table describes the status possibilities for each.

LED	LED Color	Meaning of the LED

LINK	green	Indicates a successful link has been established.
	blinking	Indicates the port is attempting to establish a link.
	green
	off	Indicates the port has not established a link with another device.

TX/RX	green	Indicates the port is successfully passing packets back and forth to a
		destination device.
	blinking	Indicates the port is attempting to pass packets back and forth to a
	green	destination device.
	off	Indicates the port does not have a device connected to it.

NetScreen-5000 Series

V

Image 61

Contents NETSCREEN-5000 Series Copyright Notice Table of Contents Servicing the Device IX-I Table of Contents Guide Organization PrefaceJuniper Networks Netscreen Publications Command Line Interface CLI ConventionsOverview1 NetScreen-5400 NetScreen-5200NETSCREEN-5000 Series NetScreen-5400 Power Recommendations NetScreen-5200 Power RecommendationsPower Supplies AC Power Supply DC Power SupplyNETSCREEN-5000 Modules FAN Modules5000-M Management Module Management Modules5000-M2 Management Module 5000-8G SPM Secure Port Modules5000-2G24FE SPM 5000-8G2 SPM Part Number Description Distance Fiber Type 5000-2XGE SPMOverview User’s Guide Installing the Device Equipment Rack Installation Guidelines General Installation GuidelinesMounting the NETSCREEN-5000 Series NetScreen-5200 Front and Rear MountNetScreen-5400 Front Mount NetScreen-5200 Mid-MountInstalling and Wiring a DC Power Supply Installing and Connecting the AC Power Supply48V COMThumbscrew Power Establishing AN HA Connection Connecting the NETSCREEN-5000 Series to a Router or SwitchInstalling the Device User’s Guide Configuring the Device Route Mode Transparent ModeOperational Modes NETSCREEN-5000 Interfaces NetScreen-5200 InterfacesNetScreen-5400 Interfaces Configurable InterfacesEstablishing a Terminal Emulator Connection Performing Initial Connection and ConfigurationUpgrading the Firmware During the Boot Process Setting Port and Interface IP Addresses Changing Your Admin Name and PasswordViewing Current Interface Settings Setting the IP Address of the Management InterfaceSetting the IP Address for the Untrust Zone Interface Setting the IP Address for the Trust Zone InterfaceConfiguring the Device for Telnet and Webui Sessions Starting a Console Session Using TelnetAllowing Outbound Traffic Establishing a GUI Management Session Starting a Console Session Using DialupHttp//10.100.2.183 Configuring the Chassis AlarmConfiguring Aggregate Interfaces Configuring Jumbo FramesFollowing CLI command unset admin device-reset Using CLI Commands to Reset the DevicePress the y key Following message appears Servicing the Device Removing and Reseating Modules Replacing a DC Power SupplyReplacing the FAN Module Replacing AN AC Power SupplyNetScreen-5200 Fan Module Remove the fan tray See NetScreen-5200 Fan Module on NetScreen-5200 Fan Tray FilterNetScreen-5400 Fan Module Replacing the Fan Module Remove the fan tray See NetScreen-5400 Fan Module on NetScreen-5400 Fan Tray FilterRemoving and Installing a MINI-GBIC Transceiver Connecting and Disconnecting Gigabit Ethernet CablesServicing the Device User’s Guide Specifications NETSCREEN-5200 Attributes Electrical SpecificationNETSCREEN-5400 Attributes EnvironmentalConnectors Safety CertificationsNebs Certifications EMI CertificationsAppendix a Specifications Port Descriptions and LED Status B MGT Module Port DescriptionsFollowing table details the ports on the 5000-8G2 SPM Module LED DescriptionsStatus LED States Interpreting Status LEDs for the Management ModulesInterpreting Ethernet Port Status LEDs for All Modules Interpreting Status LEDs for the Secure Port ModuleInterpreting Power Supply LED Status for the NetScreen-5400 Interpreting Power Supply LED Status for the NetScreen-5200Power Supply Leds Single SPM InstalledFAN LED Viii Index IX-II