Juniper Networks 5000 manual Configuring the Device

Page 29

Configuring the Device

3

 

This chapter describes how to perform initial configuration on the NetScreen-5000 Series once you have mounted it in a rack or desktop, plugged in the necessary cables, and turned the power on. Topics in this chapter include:

“Operational Modes” on page 22

“Transparent Mode” on page 22

“Route Mode” on page 22

“The NetScreen-5000 Interfaces” on page 23

“NetScreen-5200 Interfaces” on page 23

“NetScreen-5400 Interfaces” on page 24

“Configurable Interfaces” on page 24

“Performing Initial Connection and Configuration” on page 25

“Establishing a Terminal Emulator Connection” on page 25

“Upgrading the Firmware During the Boot Process” on page 26

“Changing Your Admin Name and Password” on page 27

“Setting Port and Interface IP Addresses” on page 27

“Configuring the Device for Telnet and WebUI Sessions” on page 29

“Starting a Console Session Using Telnet” on page 29

“Starting a Console Session Using Dialup” on page 30

“Establishing a GUI Management Session” on page 30

“Configuring the Chassis Alarm” on page 31

“Configuring Jumbo Frames” on page 32

“Configuring Aggregate Interfaces” on page 32

“Using CLI Commands to Reset the Device” on page 33

Note: You must register your product at www.juniper.net/support so that certain ScreenOS services, such as the Deep Inspection Signature Service, can be activated on the device. After registering your product, use the WebUI or CLI to obtain the subscription for the service. For more information about registering your product and obtaining subscriptions for specific services, see the “System Parameters” chapter in the NetScreen Concepts & Examples ScreenOS Reference Guide.

NetScreen-5000 Series

21

Image 29
Contents NETSCREEN-5000 Series Copyright Notice Table of Contents Servicing the Device IX-I Table of Contents Guide Organization PrefaceJuniper Networks Netscreen Publications Command Line Interface CLI ConventionsOverview1 NETSCREEN-5000 Series NetScreen-5200NetScreen-5400 Power Supplies NetScreen-5200 Power RecommendationsNetScreen-5400 Power Recommendations AC Power Supply DC Power SupplyNETSCREEN-5000 Modules FAN Modules5000-M Management Module Management Modules5000-M2 Management Module 5000-8G SPM Secure Port Modules5000-2G24FE SPM 5000-8G2 SPM Part Number Description Distance Fiber Type 5000-2XGE SPMOverview User’s Guide Installing the Device Equipment Rack Installation Guidelines General Installation GuidelinesMounting the NETSCREEN-5000 Series NetScreen-5200 Front and Rear MountNetScreen-5400 Front Mount NetScreen-5200 Mid-MountInstalling and Wiring a DC Power Supply Installing and Connecting the AC Power Supply48V COMThumbscrew Power Establishing AN HA Connection Connecting the NETSCREEN-5000 Series to a Router or SwitchInstalling the Device User’s Guide Configuring the Device Operational Modes Transparent ModeRoute Mode NETSCREEN-5000 Interfaces NetScreen-5200 InterfacesNetScreen-5400 Interfaces Configurable InterfacesEstablishing a Terminal Emulator Connection Performing Initial Connection and ConfigurationUpgrading the Firmware During the Boot Process Setting Port and Interface IP Addresses Changing Your Admin Name and PasswordViewing Current Interface Settings Setting the IP Address of the Management InterfaceSetting the IP Address for the Untrust Zone Interface Setting the IP Address for the Trust Zone InterfaceAllowing Outbound Traffic Starting a Console Session Using TelnetConfiguring the Device for Telnet and Webui Sessions Establishing a GUI Management Session Starting a Console Session Using DialupHttp//10.100.2.183 Configuring the Chassis AlarmConfiguring Aggregate Interfaces Configuring Jumbo FramesFollowing CLI command unset admin device-reset Using CLI Commands to Reset the DevicePress the y key Following message appears Servicing the Device Removing and Reseating Modules Replacing a DC Power SupplyReplacing the FAN Module Replacing AN AC Power SupplyNetScreen-5200 Fan Module Remove the fan tray See NetScreen-5200 Fan Module on NetScreen-5200 Fan Tray FilterNetScreen-5400 Fan Module Replacing the Fan Module Remove the fan tray See NetScreen-5400 Fan Module on NetScreen-5400 Fan Tray FilterRemoving and Installing a MINI-GBIC Transceiver Connecting and Disconnecting Gigabit Ethernet CablesServicing the Device User’s Guide Specifications NETSCREEN-5200 Attributes Electrical SpecificationNETSCREEN-5400 Attributes EnvironmentalConnectors Safety CertificationsNebs Certifications EMI CertificationsAppendix a Specifications Port Descriptions and LED Status B MGT Module Port DescriptionsFollowing table details the ports on the 5000-8G2 SPM Module LED DescriptionsStatus LED States Interpreting Status LEDs for the Management ModulesInterpreting Ethernet Port Status LEDs for All Modules Interpreting Status LEDs for the Secure Port ModuleInterpreting Power Supply LED Status for the NetScreen-5400 Interpreting Power Supply LED Status for the NetScreen-5200Power Supply Leds Single SPM InstalledFAN LED Viii Index IX-II