Hypertec ISDN 10T Router manual Installing the Hypertec Isdn 10T Router NMS, Software Installation

Page 10

Installation

Software Installation

The Hypertec ISDN 10T Router software diskettes contain two software packages, namely, NMS and EasyWeb.

The Hypertec ISDN 10T Router Network Management System (NMS) is used to manage the Hypertec ISDN 10T Router from a Windows based PC equipped with a TCP/IP protocol stack. NMS communicates with the Hypertec ISDN 10T Router through Simple Network Management Protocol (SNMP)

NMS consists of two applications, One is the SNMP management which is used to configure the Hypertec ISDN 10T Router router and the other is Remote Monitor which displays the Hypertec ISDN 10T Router real-time status in a front panel like mini-window.

EasyWeb, which also runs on a Windows95/NT (not Windows 3.1) based PC on the attached Ethernet. EasyWeb is a proxy web server and acts as an adjunct to a PC web browser. EasyWeb translates HTTP requests into SNMP requests and forwards them to the Hypertec ISDN 10T Router. Likewise, SNMP responses from the Hypertec ISDN 10T Router are translated into HTTP responses and delivered to the browser. EasyWeb makes it possible to manage the Hypertec ISDN 10T Router from any PC with a web browser.

Installing the Hypertec ISDN 10T Router NMS

1.Select a Windows-based PC on the Ethernet network that is attached to the Hypertec ISDN 10T Router directly or indirectly through another repeater. Insert the supplied Hypertec ISDN 10T Router NMS software diskette into the disk drive.

2.Under Windows 95/NT select Run in the Start Menu and type A:\Setup.exe in the Open field and click OK.

Under Window 3.1 select Run in the File menu of the Program Manager window and type A:\Setup.exe in the Command Line, and click OK.

Note: If the designation of the floppy disk drive is B: use this instead of A:.

3.The setup program will assign a default directory for the installed program. You will be asked to either accept the default directory or assign a different one.

4.When the setup program is finished, you will see:

NMS and Remote Monitor in the Start/Programs menu under Windows 95/NT.

The NMS and Remote Monitor icons under Windows 3.1 (see Figure 0-3, Hypertec ISDN 10T Router Software Icons) are :.

Figure 0-3, Hypertec ISDN 10T Router Software Icons

5.When the setup is complete, the programs may be launched. Details of launching and operating the programs are described in Chapter 3.

3

Image 10

Contents Hypertec Isdn 10T Router Introduction Contents Hypertec Isdn 10T Router Ethernet Internet/IntranetNetwork Management Analog ServicesSecurity Router SoftwareAbout this Manual Hypertec Isdn 10T Router Packing ListHardware Installation GeneralInstallation Installing the Hypertec Isdn 10T Router NMS Software InstallationInstalling EasyWeb if there is an installed Http server Uninstalling NMSInstalling EasyWeb if there is no installed Http server Installing EasyWebExample using the Microsoft Personal web server on Win95 Isdn OverviewInterface Type National Isdn Variants Default Setting Isdn Switch VariantsPhysical Interface 56K/64K Rate Adaption Service Profile Identifiers SPIDsService type Number of channels Isdn Permanent Nailed CircuitBridging Data Communication ServicesRouting Routing Table Internet and Intranet Connection ProfilesIP Address and Subnet Mask IP Address, Un-Numbered, or NumberedDynamic IP address Assignment Unnumbered Isdn LinkIPX Address IPX Frame TypeRIP IPX SpoofingMultilink PPP F1 F1 F2 F2 PacketDial on Demand Bandwidth on DemandCalling Line Identification Clid Packet Filtering, IP Access ListData Compression CallbackNAT Introduction Line Provisioning ServiceVoice Preemption Ordering the Isdn LineIsdn Switches and Services Supported Switch type Isdn ServiceProvisioning the Isdn Line Using Isdn Order CodesCapability Isdn Service Package Capability PackagesSolution Sets Solution Set Isdn ServiceNational Isdn 1 & National Isdn Switch Feature ValueMultiple Subscriber Numbering MSN More Information Terminal TypesIntroduction General NMS Menu Structure Configura Login NMS WindowsExample Sub-Menu window NMS System Menus Required Information NMS ToolbarDescription Source Required or Optional Starting NMS Logging Into NMSQuick Configuration Menu Local Router NameDial-out Password Network Address Translation EnableDial-out Authentication Local IP MaskIsdn Switch Type Phone NumberLocal Menu Call-in AuthenticationCall-in Password Local Ethernet Sub-menuDevice Name Switch TypeChannel Alarm Threshold IP AddressLocal Isdn Window Data Usage Phone 1 UsagePhone 2 Usage Route TableARP Proxy Access ListRIP Protocol Subnet Mask Local Dhcp Sub-menuIP Address Pool Start Address, End Address Gateway AddressDomain Name Dhcp EnableData Service Lease DurationRemote Router Name Internet PPP WindowUtil Ave IntervalIdle Internet IP Sub-menu Remote Snmp EnableIP Enable IP Address of Remote EthernetRemote End IP Address of Isdn Line IP Mask of Remote EthernetLocal End IP Address of Isdn Line IP Mask of Isdn LineHttp Server Starting PortFTP Server Telnet ServerClid Calling Num12, Intranet PPP Window Encapsulation Protocol Intranet IP Menu 13, Intranet IP WindowIntranet IPX Menu 14, Intranet IPX Window IPX Route Table SpoofingAge IPX SAP TableSnmp Menu 15, Snmp WindowName Trap EnableDescription LocationErrors BroadcastsB1 Channel Status DiscardsChannel Status B2 Channel StatusChannels In Use Error FramesChannels Up Time B1 UtilisationClear Trap List Trouble ShootingDetail Log Enable Trap HistoryPPP Success Isdn Data Call SuccessPPP Attempts Managing the Hypertec Router from a Console20, Console Login Screen 21, Console Quick Config Screen Managing the Hypertec Router from a BrowserRouter Isdn Express Route Troubleshooting Monitor the status of the B channel LEDs Monitor the status of the D channel LEDMonitor the status of the Ethernet LEDs If your are unable to make voice call IndexIf your are unable to make a data call Index Spid SPID-1 SPID-2 Product Warranty