Zenith XBS245 warranty Connections Basic TV Connections, Optional TV Connections

Page 12

Connections (Continued)

Basic TV Connections

Make one of the following connections, depending on the capabilities of your TV.

RF coaxial connection

Connect the RF.OUT jack on the DVD+VCR to the antenna in jack on the TV using the 75-ohm Coaxial Cable supplied (R).

ote

If you use this connection, tune the TV to the DVD+VCR’s RF output channel (CH 3 or 4).

How to set the DVD+VCRs RF output channel When the DVD+VCR is turned off, press and hold CH/PRESET (v/V) on the front panel for about five seconds to change the RF output channel (CH 03 or CH 04). “RF 03” or “RF 04” appears in the display win- dow.

Audio/Video connection

Connect the DVD/VCR VIDEO OUT jack on the

1 DVD+VCR to the video in jack on the TV using the supplied video cable (V).

2 Connect the Left and Right DVD/VCR AUDIO OUT jacks on the DVD+VCR to the audio left/right in jacks on the TV (A) using the supplied audio cables.

ote

If you use this connection, set the TV’s source selector to VIDEO.

Rear of TV

ANTENNA

AUDIO INPUT

VIDEO

COMPONENT/PROGRESSIVE

S-VIDEO

INPUT

INPUT

 

SCAN VIDEO INPUT

INPUT

 

L

R

L

Pr

Pb

Y

 

R

A

V

C

S

Rear of DVD+VCR

Optional TV Connections

otes

DVD playback can ONLY be done using the S-VIDEO OUT and COMPONENT VIDEO OUT/PROGRESSIVE SCAN connection options below. The tuner and VCR will still output through the RF.OUT (R) or DVD/VCR OUT (A, V) jack. (See left)

When using the COMPONENT VIDEO OUT/PRO- GRESSIVE SCAN jacks, set the VIDEO OUTPUT switch to COMPONENT/PROGRESSIVE SCAN.

When using the S-VIDEO OUT jack, set the VIDEO OUTPUT switch to S-VIDEO.

S-Video Connection

1to the S-Video in jack on the TV using the supplied S-Video cable (S).Connect the S-VIDEO OUT jack on the DVD+VCR

2the DVD+VCR to the audio left/right in jacks on the TV using the supplied audio cables (A).Connect the Left and Right AUDIO OUT jacks on

Component Video (Color Stream®) connection

1GRESSIVE SCAN jacks on the DVD+VCR to the

corresponding in jacks on the TV using user-sup- plied Y Pb Pr cables (C).Connect the COMPONENT VIDEO OUT/PRO-

2the DVD+VCR to the audio left/right in jacks on the TV (A) using the supplied audio cables.Connect the Left and Right AUDIO OUT jacks of

Progressive Scan (ColorStream® pro) connection

If your television is a high-definition or “digital ready” television, you may take advantage of the DVD+VCR’s progressive scan output for the highest video resolution possible.

If your TV does not accept the Progressive Scan for- mat, the picture will appear scrambled if you try Progressive Scan on the DVD+VCR.

1PROGRESSIVE SCAN jacks on the DVD+VCR to

the corresponding in jacks on the TV using an optional Y Pb Pr cable (C).Connect the COMPONENT VIDEO OUT/

2the DVD+VCR to the audio left/right in jacks on the TV (A) using the supplied audio cables.Connect the Left and Right AUDIO OUT jacks of

otes

Set the Progressive Scan to “On” on the DVD setup menu for progressive signal, see page 23.

Progressive scan does not work with the analog video connections (yellow VIDEO OUT jack).

12

Image 12
Contents Installation and Operating Guide Warranty Safety Precautions Regulatory Information FCC PartImportant Safety Instructions Table of Contents Remote control battery installation Remote Control Operation RangeBefore Use Playable DiscsPrecautions About SymbolsFront Panel Indicates sound mode is Display WindowDigital Audio PrologicRemote Control Rear Panel RF OUT DVD/VCR OUTANT.IN Digital Audio in OpticalConnecting Antenna/Cable TV to ConnectionsConnections Basic TV Connections Optional TV ConnectionsConnections Speaker System Connections Speaker PositioningDVD+VCR Connections Radio Antenna Connections Digital Device ConnectionsGame Device Hdtv Receiver Rear of DVD+VCR Front of DVD+VCR Selecting the Input/Output Source VCR RadioBefore Operation Sound Mode Descriptions Mini Glossary for Sound ModeSurround OFF 2CH Stereo Sound Mode When DVD is insertedWhen DVD is inserted and Prologic II indicator lights Sound LevelDelay Time Setting Surround delay time settingCenter delay time setting Dolby Digital mode only Before OperationBefore Operation VCR Mode On-Screen Display OSD Setting the On-Screen DisplayMenu Selection Before Operation VCR Mode Using the VCR Setup Menu Channel SelectionBefore Operation VCR Mode Setting the Clock Press Menu when finished OteAuto Clock Set Manual Clock SetBefore Operation DVD Mode General ExplanationOn-Screen Display On-screen display operationBefore Operation DVD Mode Initial Settings Initial Settings General OperationLanguage PictureParental Control Rating DVDCountry Code DVD Changing the 4-digit codeVCR Mode Tape Playback Normal Playback Special Effect PlaybackVCR Mode Tape Recording Normal Recording Timer RecordingTo pause the recording To record one TV program while watching anotherVCR Mode Tape Recording Checking Erasing the Timer ProgramProgram Priority Instant Timer Recording One-Touch Record Checking the Recording TimeTo extend the Recording Time Dubbing and EditingVCR Mode Tape Recording Sound Setup VCR Mode Other Features Tape Counter Memory Feature Additional InformationDVD Mode Operation Playing a DVD General FeaturesMoving to another Title DVD Moving to another ChapterDVD Mode Operation General Features Special DVD Features DVD DVD Mode Audio CD Operation Playing Audio CDs and MP3 discs Programmed Playback with Audio CD and MP3 Discs Repeat Programmed TracksErasing a Track from Program List Erasing the Complete Program ListDVD Mode Additional Information Video Mode Setting DVDScreen Saver About MP3Radio Operation Presetting Radio Stations To listen to non-preset radio stationsListening to the Radio To clear all the memorized stationsTroubleshooting Symptom Cause SolutionPlace the disc with the playback side down Camcorder image is not Symptom Cause Correction Audio in OpticalMoisture Condensation Language Code List Code LanguageCountry Code List Code CountrySpecifications Accessory SpeakersAmplifier Line 1, Line 2, OpticalReference Page Reference Zenith Electronics Corporation