Zenith XBS245 warranty Instant Timer Recording One-Touch Record, Checking the Recording Time

Page 28

VCR Mode Tape Recording (Continued)

Instant Timer Recording (One-Touch Record)

Instant Timer Recording allows you to make a recording easily of a preset length without using the program timer.

Preparation:

Turn on the power of both the DVD+VCR and the TV.

Be sure the TV is tuned to the DVD+VCR output channel (3 or 4). If a direct VIDEO/AUDIO connection is made between the DVD+VCR and the TV, set the TV’s source selector to VIDEO.

1Insert a video cassette with the safety tab intact.

2or number (0-9).

The channel number appears on the TV screen.

If you are recording from another source via audio/video

input jacks (at the Rear or Front panel), select LINE1 (rear jacks) or LINE2 (front jacks) by using INPUT.Select the desired channel using CH/TRK (v/V)

Set the desired recording speed (SP or EP)

3 using SPEED.

The tape speed will appear on the TV screen.

4The menu as illustrated, will appear on the TV screen. Recording will start. (The TIMER indicator will light)Press REC/ITR (z) twice.

5recording time length.

At the end of the recording, the DVD+VCR will stop recording and shut off.

During Instant Timer Recording, changing the channel

on the DVD+VCR will not be possible.

You can stop the recording by pressing STOP (x).Press REC/ITR (z) repeatedly to select the

INSTANT TIMER RECORD (ONE-TOUCH RECORD) MENU

ONE-TOUCH RECORD

0H30M

..... 9H00M 0H00M

 

 

CHANNEL

2

 

 

 

 

 

SPEED

SP

 

 

 

Length Display

START

NOW

(each additional press of

REC/ITR (z) increases recording

LENGTH

0H30M

 

 

 

 

 

time 30 minutes)

Checking the Recording Time

Press REC/ITR (z) once to check the recording time. The recalled setting will automatically return to the TV screen after 6 seconds.

To extend the Recording Time

The recording time can be extended anytime by press- ing REC/ITR (z).

Subsequent presses result in advancing the recording time by 30-minute increments.

otes

Dubbing and Editing

If you wish to edit or dub your camcorder (or another VCR) recordings to this DVD+VCR, the rear (or Front) panel mounted Audio and Video (A/V) input jacks make the connections quick and easy. These direct A/V jacks will also provide better picture results than using the RF jack on the rear panel.

1outputs to your DVD+VCR as illustrated on page 14.Connect the camcorders (or another VCRs) A/V

2 Set the input channel “LINE2”. (press INPUT twice to select LINE2.)

If you have connected your DVD+VCR to the A/V input jacks on the rear of DVD+VCR, you should select the input channel LINE1 by using INPUT.

3VCR). If you have a TV attached to your DVD+VCR, you can see the video playing.Play the tape in the camcorder (or another

When you want recording to begin, press

4 DVD+VCRs REC/ITR (z) once to start.

ote

Before recording, please confirm the recording start position.

Copying from DVD to VCR

This unit allows you to copy the contents of a DVD to a VHS tape with a press of the COPY button.

ote

If the DVD you are attempting to copy is copy protect- ed, you will not be able to copy the disc. It is not per- mitted to copy Macrovision encoded DVDs. “COPY LOCK” is displayed in the display window.

1Insert the disc you wish to copy in the DVD deck and close the disc tray.Insert Disc

2Insert a blank VHS video tape into the VCR deck.Insert a VHS Tape

3The DVD will go into Play mode and the VCR will go into Record mode.

If the DVD disc menu appears, you may need to press

PLAY (N) manually to begin copying.Press the COPY button on the unit front panel.

4When the DVD is finished playing, press the VCR on the remote control and then press STOP (x) to end copying.

You must stop the Copy process manually when the

DVD movie ends, or the unit may replay and record over and over again.Stop the Copy Process

ote

If you press PAUSE/STEP (X) during instant timer record- ing, the DVD+VCR will enter the recording pause mode. Instant timer recording is cancelled.

If the DVD+VCR is set to “0H00M”, the DVD+VCR goes to normal recording mode.

When you stop the DVD playback during copying, the record- ing on VCR is stopped automatically.

28

Image 28
Contents Installation and Operating Guide Warranty Safety Precautions Regulatory Information FCC PartImportant Safety Instructions Table of Contents Remote control battery installation Remote Control Operation RangeBefore Use Playable DiscsPrecautions About SymbolsFront Panel Indicates sound mode is Display WindowDigital Audio PrologicRemote Control Rear Panel RF OUT DVD/VCR OUTANT.IN Digital Audio in OpticalConnecting Antenna/Cable TV to ConnectionsConnections Basic TV Connections Optional TV ConnectionsSpeaker Positioning Connections Speaker System ConnectionsDVD+VCR Digital Device Connections Connections Radio Antenna ConnectionsGame Device Hdtv Receiver Rear of DVD+VCR Front of DVD+VCR Selecting the Input/Output Source VCR RadioMini Glossary for Sound Mode Before Operation Sound Mode DescriptionsSurround OFF 2CH Stereo Sound Mode When DVD is insertedWhen DVD is inserted and Prologic II indicator lights Sound LevelDelay Time Setting Surround delay time settingCenter delay time setting Dolby Digital mode only Before OperationSetting the On-Screen Display Before Operation VCR Mode On-Screen Display OSDMenu Selection Before Operation VCR Mode Using the VCR Setup Menu Channel SelectionBefore Operation VCR Mode Setting the Clock Press Menu when finished OteAuto Clock Set Manual Clock SetBefore Operation DVD Mode General ExplanationOn-Screen Display On-screen display operationBefore Operation DVD Mode Initial Settings Initial Settings General OperationLanguage PictureParental Control Rating DVDCountry Code DVD Changing the 4-digit codeVCR Mode Tape Playback Normal Playback Special Effect PlaybackVCR Mode Tape Recording Normal Recording Timer RecordingTo pause the recording To record one TV program while watching anotherChecking Erasing the Timer Program VCR Mode Tape RecordingProgram Priority Instant Timer Recording One-Touch Record Checking the Recording TimeTo extend the Recording Time Dubbing and EditingVCR Mode Tape Recording Sound Setup VCR Mode Other Features Tape Counter Memory Feature Additional InformationDVD Mode Operation Playing a DVD General FeaturesMoving to another Title DVD Moving to another ChapterDVD Mode Operation General Features Special DVD Features DVD DVD Mode Audio CD Operation Playing Audio CDs and MP3 discs Programmed Playback with Audio CD and MP3 Discs Repeat Programmed TracksErasing a Track from Program List Erasing the Complete Program ListDVD Mode Additional Information Video Mode Setting DVDScreen Saver About MP3Radio Operation Presetting Radio Stations To listen to non-preset radio stationsListening to the Radio To clear all the memorized stationsSymptom Cause Solution TroubleshootingPlace the disc with the playback side down Camcorder image is not Audio in Optical Symptom Cause CorrectionMoisture Condensation Language Code List Code LanguageCountry Code List Code CountrySpecifications Accessory SpeakersAmplifier Line 1, Line 2, OpticalReference Page Reference Zenith Electronics Corporation