Zenith XBS245 warranty Radio Operation Presetting Radio Stations, Listening to the Radio

Page 37

Radio Operation

Presetting Radio Stations

You can preset 30 stations for FM and AM. Before tun- ing, make sure that you have turned down the volume to the minimum.

Press RADIO.

1 FM or AM appears in the display window and radio infor- mation appears on the TV screen.

2 Each time you press RADIO, you toggle between FM and AM.

3for about two seconds until the frequency indi- cation starts to change, then release.

Scanning stops when the DVD Receiver tunes in a

station. “STEREO” (for stereo program) appear in the dis- play window.Press and hold TUNING (v/V) on the front panel

Press MEMORY.

4 A preset number will flash in the display window.

5 Use TUNING (v/V) on the front panel to select the preset number.

Press MEMORY again.

6 The station is stored.

7Repeat steps 3 to 6 to store other stations.

To tune in a station with a weak signal

Press TUNING (v/V) repeatedly in step 3 to tune in the station manually.

To clear all the memorized stations

Press and hold MEMORY for about three seconds and “MEM CLEAR” appears in the display window and then press MEMORY again, the stations are cleared.

ote

If all stations have already been entered, MEM FULL message will appear in the display window for a moment and then a preset number will flash. To change the preset number, follow the steps 5-6 as above.

Listening to the Radio

Preset radio stations in the DVD+VCR’s memory first (see “Presetting radio stations” on the left side).

Press RADIO

1 FM or AM appears in the display window and radio information appears on the TV screen. The last received station is tuned in.

2 Press PRESET (v/V) repeatedly to select a pre - set station.

Each time you press the button, the DVD+VCR tunes in one preset station at a time.

3front panel or by pressing VOLUME + or – on the remote control repeatedly.Adjust the volume by rotating VOLUME on the

To turn off the radio

Press POWER to turn the DVD+VCR off or select another function mode (DVD, VCR, or AUX).

To listen to non-preset radio stations

Use manual or automatic tuning in step 2.

For manual tuning, press TUNING (v/V) on the front panel repeatedly.

For automatic tuning, press and hold TUNING (v/V) for about two seconds on the front panel.

For your reference

If an FM program is noisy

Press AUDIO so that “STEREO” disappears in the display window. There will be no stereo effect, but the reception will improve. Press the button again to restore the stereo effect.

To improve reception

Realign the antenna.

OPERATION

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Installation and Operating Guide Warranty Regulatory Information FCC Part Safety PrecautionsImportant Safety Instructions Table of Contents Remote Control Operation Range Remote control battery installationBefore Use Playable DiscsAbout Symbols PrecautionsFront Panel Display Window Indicates sound mode isDigital Audio PrologicRemote Control RF OUT DVD/VCR OUT Rear PanelANT.IN Digital Audio in OpticalConnections Connecting Antenna/Cable TV toOptional TV Connections Connections Basic TV ConnectionsSpeaker Positioning Connections Speaker System ConnectionsDVD+VCR Digital Device Connections Connections Radio Antenna ConnectionsGame Device Hdtv Receiver Rear of DVD+VCR Front of DVD+VCR VCR Radio Selecting the Input/Output SourceMini Glossary for Sound Mode Before Operation Sound Mode DescriptionsSurround OFF 2CH Stereo When DVD is inserted Sound ModeWhen DVD is inserted and Prologic II indicator lights Sound LevelSurround delay time setting Delay Time SettingCenter delay time setting Dolby Digital mode only Before OperationSetting the On-Screen Display Before Operation VCR Mode On-Screen Display OSDMenu Selection Channel Selection Before Operation VCR Mode Using the VCR Setup MenuPress Menu when finished Ote Before Operation VCR Mode Setting the ClockAuto Clock Set Manual Clock SetGeneral Explanation Before Operation DVD ModeOn-Screen Display On-screen display operationInitial Settings General Operation Before Operation DVD Mode Initial SettingsLanguage PictureRating DVD Parental ControlCountry Code DVD Changing the 4-digit codeSpecial Effect Playback VCR Mode Tape Playback Normal PlaybackTimer Recording VCR Mode Tape Recording Normal RecordingTo pause the recording To record one TV program while watching anotherChecking Erasing the Timer Program VCR Mode Tape RecordingProgram Priority Checking the Recording Time Instant Timer Recording One-Touch RecordTo extend the Recording Time Dubbing and EditingVCR Mode Tape Recording Sound Setup Additional Information VCR Mode Other Features Tape Counter Memory FeatureGeneral Features DVD Mode Operation Playing a DVDMoving to another Title DVD Moving to another ChapterDVD Mode Operation General Features Special DVD Features DVD DVD Mode Audio CD Operation Playing Audio CDs and MP3 discs Repeat Programmed Tracks Programmed Playback with Audio CD and MP3 DiscsErasing a Track from Program List Erasing the Complete Program ListVideo Mode Setting DVD DVD Mode Additional InformationScreen Saver About MP3To listen to non-preset radio stations Radio Operation Presetting Radio StationsListening to the Radio To clear all the memorized stationsSymptom Cause Solution TroubleshootingPlace the disc with the playback side down Camcorder image is not Audio in Optical Symptom Cause CorrectionMoisture Condensation Code Language Language Code ListCode Country Country Code ListSpecifications Speakers AccessoryAmplifier Line 1, Line 2, OpticalReference Page Reference Zenith Electronics Corporation
Top Page Image Contents