Zenith XBS245 warranty VCR Mode Tape Playback Normal Playback, Special Effect Playback

Page 25

VCR Mode Tape Playback

Normal Playback

Preparation:

Turn on the TV.

Tune the TV to the DVD+VCR output channel (CH 3 or 4) or set the TV’s source selector to VIDEO.

If a direct VIDEO/AUDIO connection is made between the DVD+VCR and the TV, set the TV’s source selector to VIDEO. Set the Output Source to VCR as shown in Selecting the Input/Output Source on page 15.

1

Insert a prerecorded video cassette.

The

indicator will light and the DVD+VCR will

power-up automatically.

Make sure that the TIMER indicator in the display window is not lighted. If it is, press POWER once.

If a tape without a safety tab is inserted, the unit will start playback automatically.

2PLAY appears on the TV screen .Press PLAY (N) once.

It is not necessary to select the tape speed for play- back. It will be automatically selected by the DVD+VCR. In playback, the TV/VCR selector switches to VCR mode automatically.

3STOP appears on the TV screen.Press STOP (x) to stop playback.

If the tape reaches the end before STOP (x) is pressed, the DVD+VCR will automatically stop, rewind and eject the tape, and turn itself off.

Tracking Control

Auto Tracking

The automatic tracking function adjusts the picture to remove snow or streaks.

The AUTO TRACKING function works in the following cases:

A tape is played back for the first time.

Tape speed (SP, LP, EP) changes.

Streaks or snow appear because of scratches on the tape.

Manual Tracking

If noise appears on the screen during playback, press either CH/TRK (v/V) on the remote control or CH/PRESET (v/V) on the front panel until the noise on the screen is reduced.

In case of vertical jitter, adjust these controls very carefully. Tracking is automatically reset to normal when the tape is ejected or the power cord is unplugged for more than 3 sec- onds.

Special Effect Playback

Special effects playback notes

Horizontal lines (noise bars) will appear on the TV screen. This is normal.

The audio is automatically muted during special effect modes, so there is no sound during search.

During the high-speed picture search modes, a short time is needed to stabilize tape speed when re-entering the PLAY mode. Slight interference may be observed during this time.

Search

This function lets you quickly and visually search for a desired tape section in either direction: forward and reverse.

1Press BACKWARD (.) or FORWARD (>) during playback.

The DVD+VCR will be activated in the SEARCH mode.

If the DVD+VCR is left in the SEARCH mode for more than 3 minutes, the DVD+VCR will automatically enter the PLAY mode, to protect the tape and video heads.

2To return to playback, press PLAY (N).

Still Picture and Frame-by-Frame Playback

1Press PAUSE/STEP (X) during playback. A still picture appears on the TV screen.

If a still picture vibrates vertically, stabilize it by using CH/TRK (v/V) on the remote control.

If the DVD+VCR is left in the STILL mode for more than 5 minutes, the DVD+VCR will automatically enter the STOP mode to protect the tape and video heads.

2Press PAUSE/STEP (X) repeatedly to advance the video picture one frame at a time while viewing a still picture.

3To return to playback, press PLAY (N).

Slow Motion

1While in still mode, press FORWARD (>).

The tape will be played back at a speed 1/19 times slower than the normal speed.

During slow playback, use CH/TRK (v/V) on the Remote Control to minimize noise bands.

If slow motion mode continues for more than 30 seconds, the DVD+VCR will automatically change to playback mode.

2To return to playback, press PLAY (N).

CM SKIP (Commercial Skip)

This is useful for skipping commercials or short program segments.

1Press CM SKIP in playback mode.

The tape will fast forward picture search through 30 seconds of recording.

Skipping time can be extended by using CM SKIP. Subsequent presses result in advancing the fast forward picture search time by 30-second increments (maximum 2 minutes).

2When the search is complete, the DVD+VCR will go into playback mode automatically.

OPERATION

25

Image 25
Contents Installation and Operating Guide Warranty Regulatory Information FCC Part Safety PrecautionsImportant Safety Instructions Table of Contents Remote Control Operation Range Remote control battery installationBefore Use Playable DiscsAbout Symbols PrecautionsFront Panel Display Window Indicates sound mode isDigital Audio PrologicRemote Control RF OUT DVD/VCR OUT Rear PanelANT.IN Digital Audio in OpticalConnections Connecting Antenna/Cable TV toOptional TV Connections Connections Basic TV ConnectionsSpeaker Positioning Connections Speaker System ConnectionsDVD+VCR Digital Device Connections Connections Radio Antenna ConnectionsGame Device Hdtv Receiver Rear of DVD+VCR Front of DVD+VCR VCR Radio Selecting the Input/Output SourceMini Glossary for Sound Mode Before Operation Sound Mode DescriptionsSurround OFF 2CH Stereo When DVD is inserted Sound ModeWhen DVD is inserted and Prologic II indicator lights Sound LevelSurround delay time setting Delay Time SettingCenter delay time setting Dolby Digital mode only Before OperationSetting the On-Screen Display Before Operation VCR Mode On-Screen Display OSDMenu Selection Channel Selection Before Operation VCR Mode Using the VCR Setup MenuPress Menu when finished Ote Before Operation VCR Mode Setting the ClockAuto Clock Set Manual Clock SetGeneral Explanation Before Operation DVD ModeOn-Screen Display On-screen display operationInitial Settings General Operation Before Operation DVD Mode Initial SettingsLanguage PictureRating DVD Parental ControlCountry Code DVD Changing the 4-digit codeSpecial Effect Playback VCR Mode Tape Playback Normal PlaybackTimer Recording VCR Mode Tape Recording Normal RecordingTo pause the recording To record one TV program while watching anotherChecking Erasing the Timer Program VCR Mode Tape RecordingProgram Priority Checking the Recording Time Instant Timer Recording One-Touch RecordTo extend the Recording Time Dubbing and EditingVCR Mode Tape Recording Sound Setup Additional Information VCR Mode Other Features Tape Counter Memory FeatureGeneral Features DVD Mode Operation Playing a DVDMoving to another Title DVD Moving to another ChapterDVD Mode Operation General Features Special DVD Features DVD DVD Mode Audio CD Operation Playing Audio CDs and MP3 discs Repeat Programmed Tracks Programmed Playback with Audio CD and MP3 DiscsErasing a Track from Program List Erasing the Complete Program ListVideo Mode Setting DVD DVD Mode Additional InformationScreen Saver About MP3To listen to non-preset radio stations Radio Operation Presetting Radio StationsListening to the Radio To clear all the memorized stationsSymptom Cause Solution TroubleshootingPlace the disc with the playback side down Camcorder image is not Audio in Optical Symptom Cause CorrectionMoisture Condensation Code Language Language Code ListCode Country Country Code ListSpecifications Speakers AccessoryAmplifier Line 1, Line 2, OpticalReference Page Reference Zenith Electronics Corporation