GarrettCom 1008 Magnum 1000 Workgroup Hubs, Installation and User Guide 04/02, Media, Connector

Page 29
3.3Ethernet Media Connections

Magnum 1000 Workgroup Hubs

Installation and User Guide (04/02)

3.3Ethernet Media Connections

The Magnum 1000 workgroup Hub may be used as a stand-alone hub serving the needs of a small to medium size workgroup or may be connected to a larger network environment. In either case, user connectivity is achieved using twisted pair wiring, Cat. 3 or Cat 5, UTP or STP. There may be some cases where a user device will be connected via the AUI or Bonus Port.

In applications where Magnum hubs are used to provide workgroup services within a larger network system, the rear port(s) may be connected into a larger network, rather than being used to connect to a user.

The various media types supported and their corresponding IEEE 802.3 standards and connector types are as follows:

Media

IEEE Standard

Connector

PM type

ThinNet

10BASE2

BNC

RPM-BNC, BPM-BNC

ThickNet

10BASE5

AUI (female)

RPM-AUI, BPM-AUI

Drop Cable

10BASE5

DTE (male)

RPM-DTE

Twisted Pair

10BASE-T

RJ-45

RPM-TP, BPM-TP

Fiber (mm1)

FOIRL

ST

RPM-FST, RPM-SMF, BPM-FST

Fiber (mm1)

10BASE-FL

ST or SC

RPM-FST, RPM-SMF, BPM-FST

Fiber (sgl.m2)

*

ST

RPM-SMF

1mm = multi-mode

2sgl.m = single-mode

*10 Mb operation not currently standardized by IEEE

Instructions for connecting the Magnum 1000 Workgroup Hub to each of the standard Ethernet types are given below.

3.3.1Connecting Twisted Pair (RJ-45, Unshielded or Shielded)

The following procedure describes how to connect a 10BASE-T twisted pair segment to the RJ-45 port on the front panel of the hub or to the RPM-TP or BPM-TP. The procedure is the same for both unshielded and shielded twisted pair segments.

1.Using standard 10BASE-T media, insert either end of the cable with an RJ-45 plug into the RJ-45 connector. Note that, even though the TP connector is shielded, either unshielded or shielded 10BASE-T cables and wiring may be used.

2.Connect the other end of the cable to the corresponding device.

3.When proper connection and power have been established, the port’s LINK LED will illuminate GREEN.

www . GarrettCom . com

23

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Installation and User Guide Models 1008, 1016 andMagnum Workgroup Hubs “Ten Series” www . GarrettCom . comMagnum 1008, 1016 and Workgroup Hubs Installation and User Guideand optional 48VDC, 24VDC &125VDC-powered models Installation and User Guide 04/0247823 Westinghouse Drive Fremont, CA GarrettCom, IncPhone 510 Fax 510Page APPENDIX B OPTIONAL 48V POWER SUPPLY, ADDENDUMTABLE OF CONTENTS Revisions The Magnum Line Personal Switches, 10/100MbStackable Hubs, SNMP Optional Personal Hubs, 10Mb seriesConnectors 1.0 SPECIFICATIONS 1.1 Technical Specifications PerformanceSwitches Network StandardsFor 48VDC power input option, see Appendix B Agency Approvals Power Supply InternalWarranty 1.2 Specifications - Repeater Port Modules RPMs1.4 Ordering Information Magnum 1000 Workgroup HubsMagnum Magnum Magnum 2.2 Product Description - Magnum 1000-series Workgroup Hubs 2.0 INTRODUCTION 2.1 Inspecting the Package and ProductFigure 2.2.1a Front view - Magnum 1008 Workgroup Hub 2.2.1 Magnum 1008 Workgroup HubAC Power Installation and User Guide 04/02Magnum 1000 Workgroup Hubs 115 - 230 VACFigure 2.2.2b Front view - Magnum 1024 Workgroup Hub Configurable Bonus PortRPM-FST Shown Figure 2.2.2c Rear view - Magnum 1016 and 1024 Workgroup HubsOptional PM card Basic AUI portBPM shown PM Ribbon cable with 16 pin headers2.4 Bonus Port Configuration Options - RPMs and BPMs Magnum 1000 Workgroup Hubs Installation and User Guide 04/02Bonus port for optional Basic AUI port PM card BPM shown Figure 2.4a Magnum RPM Cards RPM-BNC, RPM-AUIApprox. 3 inches 7.6 cm Figure 2.4c Physical Dimensions of Magnum Port ModulesApprox Approx. 2 inches 5.1 cm2.4.2 RPM-AUI 2.4.1 RPM-BNC2.4.3 RPM-DTE Connector RPM-FST Fiber ST, Twist-lock Connector2.4.4 JUMPER ACROSSnot used 2.4.6 RPM-SMF Single-mode FiberMagnum RPM-SMF Magnum RPM-TP 2.4.7 RPM-TP Twisted PairMagnum BPM-BNC 2.4.8 BPM-BNC2.4.9 BPM-AUI Magnum BPM-AUI2.4.11 BPM-TP 2.4.10 BPM-FSTMagnum BPM-FST 2.4.12 Special Option -- Second Bonus Port Models 1016 and LEDs Simplify Network Installation and Maintenance 2.5 Features and Benefits Low cost, stand-alone 10BASE-T connectivityInternal Universal Power Supply with Auto-ranging Workgroup connectivity into a larger networkMagnum 1000 Workgroup Hub Figure 2.6a Magnum 1000 Workgroup Hub in stand-alone configuration2.6 Applications BNC Segment RPM-BNC Server 10241008 10161024 Fiber BPMinstallation requires a 3.0 INSTALLATIONinstalled in any standard 19 inch rack Rack-mount Brackets 3.2 Powering the Magnum 1000 Workgroup Hub3.3 Ethernet Media Connections 3.3.1 Connecting Twisted Pair RJ-45, Unshielded or ShieldedMedia IEEE Standard3.3.2 Connecting ThickNet 10BASE5 AUI 3.3.4 Connecting Drop Cable 10BASE5 DTE 3.3.3 Connecting ThinNet 10BASE2 BNC3.3.5 Connecting Fiber Optic 10BASE-FL and FOIRL ST-type, “Twist-Lock Table 3.3.2 AUI Pin Assignments3.3.7 Connecting Single-Mode Fiber Optic SMF 3.3.6 Connecting Fiber Optic SMA-type, Screw-onat regular intervals you must use the color-coded strand on the associated ports at each end of the fiber optic segment3.3.9 Rack-mounting OPB Optical Power Budget = PTmin - PRminTELCO Industry and brackets are more popular inconsider as a standard for Rack-mounting purpose. TheCollisions When carrier is detected simultaneously on multiple ports, a jam pattern is generated on each port to create a collision condition. When a collision signal from one port is detected, it generates a jam pattern to the other ports Figure 4.2b Internal Packet Filtered 4.2 Magnum 1000’s with BPM Local Bridge FunctionalityPacket Forwarded Figure 4.2c External Packet MaintenanceForwarded Table 4.2 BPM FunctionalityFigure 4.2e Local Segment Isolation with a Bridge Port Module BPM 4.3 Power Requirements5.1 Before Calling for Assistance 5.0 TROUBLESHOOTING5.3 Return Material Authorization RMA Procedure 5.2 When Calling for AssistanceNo Problem Found APPENDIX A WARRANTY INFORMATIONGarrettCom, Inc 213 Hammond Ave Fremont, CA Attn. Customer Service 5.4 Shipping and Packaging InformationB1.0 SPECIFICATIONS - FOR MAGNUM 1000 WORKGROUP HUBS APPENDIX B Internal DC Power Supply OptionPower Supply Internal -48 VDC Option Power Supply Internal 24 VDC OptionB3.0 APPLICATIONS B4.0 INSTALLATIONFigure B4.1 -48VDC Terminal Block on Magnum 1000’s-48VDCThe GND can be hooked at the last B7.0 TROUBLESHOOTINGB4.1 UL Requirements B5.0 OPERATION
Top Page Image Contents