GarrettCom 1008 Magnum 1000 Workgroup Hubs, Installation and User Guide 04/02, Warranty, RPM Type

Page 8

Power Supply (Internal)

Magnum 1000 Workgroup Hubs

Installation and User Guide (04/02)

Power Supply (Internal)

AC Power Connector: IEC-type, male recessed, rear of chassis

Input Voltage: 90 to 260 VAC (auto-ranging)

Input Frequency: 47 to 63 Hz (auto-ranging)

Power Consumption: 10 watts typical, 20 watts max. P.S. rating

(For 48VDC power input option, see Appendix B).

Agency Approvals

UL Listed (UL 1950), cUL, CE

Emissions meet FCC Part 15 Class A

Warranty
Three years, return to factory	Made in USA

1.2Specifications - Repeater Port Modules (RPMs)

RPM Type :	BNC	AUI	DTE	Fiber-mm Fiber-sgl.m		TP*
Front Access	yes	yes	yes	yes	yes	yes
Connector Type	BNC-f	DB-15 f	DB-15 m	Fiber-ST Fiber-ST		RJ-45
Partition (PART)LED	yes	yes	yes	yes	yes	yes
Receive (RX) LED	yes	yes	yes	yes	yes	yes
LINK LED	n.a.	n.a.	n.a.	yes	yes	yes
Switch on Face Plate	yes**	n.a.	n.a.	n.a.	n.a.

yes***

“Fiber-mm” is multi-mode cable, normally used for 10BASE-FL installations, up to 2.0Km.

“Fiber-sgl.m” is single-mode cable, used for distant installations, up to 10.0Km.

*The RJ-45 connector is shielded; it accepts RJ-45 eight-pin plugs for unshielded and shielded twisted pair wiring.

**Internal termination switch for BNC, no "T" connector is required.

***MDI-X (Media Dependent Interface - Crossover) switch for RJ-45 up-link, no crossover cable is required.

1.3Specifications - Bridge Port Modules (BPMs)

BPM Type :	BNC	AUI	Fiber	TP*
Connector Type	BNC(f)	DB-15(f)	ST	RJ-45
Switch on FP	yes**	n.a.	n.a.	yes***
FWD-I LED	yes	yes	yes	yes
FWD-X LED	yes	yes	yes	yes
LINK LED	n.a.	n.a.	yes	yes

*The RJ-45 connector is shielded; it accepts RJ-45 eight-pin plugs for unshielded and shielded twisted pair wiring.

**Internal termination switch for BNC, no "T" connector is required.

***MDI-X (Media Dependent Interface - Crossover) switch for RJ-45 up-link, no crossover cable is required.

www . GarrettCom . com

2

Image 8

Contents Models 1008, 1016 and Installation and User GuideMagnum Workgroup Hubs “Ten Series” www . GarrettCom . comWorkgroup Hubs Installation and User Guide Magnum 1008, 1016 andand optional 48VDC, 24VDC &125VDC-powered models Installation and User Guide 04/02GarrettCom, Inc 47823 Westinghouse Drive Fremont, CAPhone 510 Fax 510Page APPENDIX B OPTIONAL 48V POWER SUPPLY, ADDENDUMTABLE OF CONTENTS Revisions Personal Switches, 10/100Mb The Magnum LineStackable Hubs, SNMP Optional Personal Hubs, 10Mb series1.0 SPECIFICATIONS 1.1 Technical Specifications Performance ConnectorsSwitches Network StandardsPower Supply Internal For 48VDC power input option, see Appendix B Agency ApprovalsWarranty 1.2 Specifications - Repeater Port Modules RPMs1.4 Ordering Information Magnum 1000 Workgroup HubsMagnum Magnum Magnum 2.0 INTRODUCTION 2.1 Inspecting the Package and Product 2.2 Product Description - Magnum 1000-series Workgroup Hubs2.2.1 Magnum 1008 Workgroup Hub Figure 2.2.1a Front view - Magnum 1008 Workgroup HubInstallation and User Guide 04/02 AC PowerMagnum 1000 Workgroup Hubs 115 - 230 VACConfigurable Bonus Port Figure 2.2.2b Front view - Magnum 1024 Workgroup HubRPM-FST Shown Figure 2.2.2c Rear view - Magnum 1016 and 1024 Workgroup HubsBasic AUI port Optional PM cardBPM shown PM Ribbon cable with 16 pin headersMagnum 1000 Workgroup Hubs Installation and User Guide 04/02 2.4 Bonus Port Configuration Options - RPMs and BPMsBonus port for optional Basic AUI port PM card BPM shown Figure 2.4a Magnum RPM Cards RPM-BNC, RPM-AUIFigure 2.4c Physical Dimensions of Magnum Port Modules Approx. 3 inches 7.6 cmApprox Approx. 2 inches 5.1 cm2.4.1 RPM-BNC 2.4.2 RPM-AUI2.4.3 RPM-DTE RPM-FST Fiber ST, Twist-lock Connector Connector2.4.4 JUMPER ACROSSnot used 2.4.6 RPM-SMF Single-mode FiberMagnum RPM-SMF 2.4.7 RPM-TP Twisted Pair Magnum RPM-TP2.4.8 BPM-BNC Magnum BPM-BNC2.4.9 BPM-AUI Magnum BPM-AUI2.4.11 BPM-TP 2.4.10 BPM-FSTMagnum BPM-FST 2.4.12 Special Option -- Second Bonus Port Models 1016 and 2.5 Features and Benefits Low cost, stand-alone 10BASE-T connectivity LEDs Simplify Network Installation and MaintenanceInternal Universal Power Supply with Auto-ranging Workgroup connectivity into a larger networkFigure 2.6a Magnum 1000 Workgroup Hub in stand-alone configuration Magnum 1000 Workgroup Hub2.6 Applications BNC Segment RPM-BNC Server 10241016 10081024 Fiber BPM3.0 INSTALLATION installation requires ainstalled in any standard 19 inch rack Rack-mount Brackets 3.2 Powering the Magnum 1000 Workgroup Hub3.3.1 Connecting Twisted Pair RJ-45, Unshielded or Shielded 3.3 Ethernet Media ConnectionsMedia IEEE Standard3.3.2 Connecting ThickNet 10BASE5 AUI 3.3.3 Connecting ThinNet 10BASE2 BNC 3.3.4 Connecting Drop Cable 10BASE5 DTE3.3.5 Connecting Fiber Optic 10BASE-FL and FOIRL ST-type, “Twist-Lock Table 3.3.2 AUI Pin Assignments3.3.6 Connecting Fiber Optic SMA-type, Screw-on 3.3.7 Connecting Single-Mode Fiber Optic SMFat regular intervals you must use the color-coded strand on the associated ports at each end of the fiber optic segmentOPB Optical Power Budget = PTmin - PRmin 3.3.9 Rack-mountingbrackets are more popular in TELCO Industry andconsider as a standard for Rack-mounting purpose. TheCollisions When carrier is detected simultaneously on multiple ports, a jam pattern is generated on each port to create a collision condition. When a collision signal from one port is detected, it generates a jam pattern to the other ports Figure 4.2b Internal Packet Filtered 4.2 Magnum 1000’s with BPM Local Bridge FunctionalityPacket Forwarded Maintenance Figure 4.2c External PacketForwarded Table 4.2 BPM Functionality4.3 Power Requirements Figure 4.2e Local Segment Isolation with a Bridge Port Module BPM5.0 TROUBLESHOOTING 5.1 Before Calling for Assistance5.2 When Calling for Assistance 5.3 Return Material Authorization RMA ProcedureAPPENDIX A WARRANTY INFORMATION No Problem FoundGarrettCom, Inc 213 Hammond Ave Fremont, CA Attn. Customer Service 5.4 Shipping and Packaging InformationAPPENDIX B Internal DC Power Supply Option B1.0 SPECIFICATIONS - FOR MAGNUM 1000 WORKGROUP HUBSPower Supply Internal -48 VDC Option Power Supply Internal 24 VDC OptionB4.0 INSTALLATION B3.0 APPLICATIONSFigure B4.1 -48VDC Terminal Block on Magnum 1000’s-48VDCB7.0 TROUBLESHOOTING The GND can be hooked at the lastB4.1 UL Requirements B5.0 OPERATION