GarrettCom 1016, 1024, 1008 Magnum 1000 Workgroup Hubs, Installation and User Guide 04/02, Rpm-Dte

Page 18

2.4.3RPM-DTE

12

1

Magnum RPM-DTE

2

1 Partition LED

2 Receive LED

Standard 15-pin male "AUI"

Magnum RPM-AUI

1

2

with slide-lock

Receive LED

Standard 15-pin female AUI,

Partition LED

Magnum 1000 Workgroup Hubs

Installation and User Guide (04/02)

used with a variety of different mini-transceivers to provide connectivity to any media type.

The RPM-AUI card is equipped with Partition (PART) and Receive (RX) LEDs. The RX LED functions the same as the RX LEDs of the RPM-BNC. The PART LED is inoperative on Model 1000 Workgroup Hubs. (Section 2.4.1 above).

The Magnum RPM-AUI card is also used for connecting Ethernet devices using standard

AUI cabling. In this situation, it is important to consider the AUI

segment length or distance to the attached device, including any

cascading. Refer to Section 3.3.2 for detailed information on the AUI

port, connector pins, and cable length requirements.

2.4.3RPM-DTE

1

2

The Magnum RPM-DTE is a module equipped with a 15-pin male DTE connector with lock posts. (The RPM-DTE is a mating connector for the RPM-AUI which has a 15-pin female connector and slide locks. The pin assignments of the two are the same). The RPM-DTE card

is designed to support direct

connections (no transceiver required) using AUI drop cables to

any device that is equipped with an AUI port. Examples of such devices

include servers, routers, bridges, hubs, and UNIX workstations.

www . GarrettCom . com

Image 18

Contents Magnum Workgroup Hubs “Ten Series” Models 1008, 1016 andInstallation and User Guide www . GarrettCom . comand optional 48VDC, 24VDC &125VDC-powered models Workgroup Hubs Installation and User GuideMagnum 1008, 1016 and Installation and User Guide 04/02Phone 510 GarrettCom, Inc47823 Westinghouse Drive Fremont, CA Fax 510APPENDIX B OPTIONAL 48V POWER SUPPLY, ADDENDUM TABLE OF CONTENTSPage Revisions Stackable Hubs, SNMP Optional Personal Switches, 10/100MbThe Magnum Line Personal Hubs, 10Mb seriesSwitches 1.0 SPECIFICATIONS 1.1 Technical Specifications PerformanceConnectors Network StandardsWarranty Power Supply InternalFor 48VDC power input option, see Appendix B Agency Approvals 1.2 Specifications - Repeater Port Modules RPMsMagnum 1000 Workgroup Hubs Magnum Magnum Magnum1.4 Ordering Information 2.0 INTRODUCTION 2.1 Inspecting the Package and Product 2.2 Product Description - Magnum 1000-series Workgroup Hubs2.2.1 Magnum 1008 Workgroup Hub Figure 2.2.1a Front view - Magnum 1008 Workgroup HubMagnum 1000 Workgroup Hubs Installation and User Guide 04/02AC Power 115 - 230 VACRPM-FST Shown Configurable Bonus PortFigure 2.2.2b Front view - Magnum 1024 Workgroup Hub Figure 2.2.2c Rear view - Magnum 1016 and 1024 Workgroup HubsBPM shown Basic AUI portOptional PM card PM Ribbon cable with 16 pin headersBonus port for optional Basic AUI port PM card BPM shown Magnum 1000 Workgroup Hubs Installation and User Guide 04/022.4 Bonus Port Configuration Options - RPMs and BPMs Figure 2.4a Magnum RPM Cards RPM-BNC, RPM-AUIApprox Figure 2.4c Physical Dimensions of Magnum Port ModulesApprox. 3 inches 7.6 cm Approx. 2 inches 5.1 cm2.4.1 RPM-BNC 2.4.2 RPM-AUI2.4.3 RPM-DTE 2.4.4 RPM-FST Fiber ST, Twist-lock ConnectorConnector JUMPER ACROSS2.4.6 RPM-SMF Single-mode Fiber Magnum RPM-SMFnot used 2.4.7 RPM-TP Twisted Pair Magnum RPM-TP2.4.9 BPM-AUI 2.4.8 BPM-BNCMagnum BPM-BNC Magnum BPM-AUI2.4.10 BPM-FST Magnum BPM-FST2.4.11 BPM-TP 2.4.12 Special Option -- Second Bonus Port Models 1016 and Internal Universal Power Supply with Auto-ranging 2.5 Features and Benefits Low cost, stand-alone 10BASE-T connectivityLEDs Simplify Network Installation and Maintenance Workgroup connectivity into a larger network2.6 Applications Figure 2.6a Magnum 1000 Workgroup Hub in stand-alone configurationMagnum 1000 Workgroup Hub BNC Segment RPM-BNC Server 10241024 10161008 Fiber BPMinstalled in any standard 19 inch rack 3.0 INSTALLATIONinstallation requires a Rack-mount Brackets 3.2 Powering the Magnum 1000 Workgroup HubMedia 3.3.1 Connecting Twisted Pair RJ-45, Unshielded or Shielded3.3 Ethernet Media Connections IEEE Standard3.3.2 Connecting ThickNet 10BASE5 AUI 3.3.5 Connecting Fiber Optic 10BASE-FL and FOIRL ST-type, “Twist-Lock 3.3.3 Connecting ThinNet 10BASE2 BNC3.3.4 Connecting Drop Cable 10BASE5 DTE Table 3.3.2 AUI Pin Assignmentsat regular intervals you must use the color-coded strand on the 3.3.6 Connecting Fiber Optic SMA-type, Screw-on3.3.7 Connecting Single-Mode Fiber Optic SMF associated ports at each end of the fiber optic segmentOPB Optical Power Budget = PTmin - PRmin 3.3.9 Rack-mountingconsider as a standard for brackets are more popular inTELCO Industry and Rack-mounting purpose. TheCollisions When carrier is detected simultaneously on multiple ports, a jam pattern is generated on each port to create a collision condition. When a collision signal from one port is detected, it generates a jam pattern to the other ports 4.2 Magnum 1000’s with BPM Local Bridge Functionality Packet ForwardedFigure 4.2b Internal Packet Filtered Forwarded MaintenanceFigure 4.2c External Packet Table 4.2 BPM Functionality4.3 Power Requirements Figure 4.2e Local Segment Isolation with a Bridge Port Module BPM5.0 TROUBLESHOOTING 5.1 Before Calling for Assistance5.2 When Calling for Assistance 5.3 Return Material Authorization RMA ProcedureGarrettCom, Inc 213 Hammond Ave Fremont, CA Attn. Customer Service APPENDIX A WARRANTY INFORMATIONNo Problem Found 5.4 Shipping and Packaging InformationPower Supply Internal -48 VDC Option APPENDIX B Internal DC Power Supply OptionB1.0 SPECIFICATIONS - FOR MAGNUM 1000 WORKGROUP HUBS Power Supply Internal 24 VDC OptionFigure B4.1 -48VDC Terminal B4.0 INSTALLATIONB3.0 APPLICATIONS Block on Magnum 1000’s-48VDCB4.1 UL Requirements B7.0 TROUBLESHOOTINGThe GND can be hooked at the last B5.0 OPERATION