EnGenius Technologies EOA7530 manual Hardware Overview, Bottom View

Page 8

Chapter 2 Hardware Overview

The following figures show the key components on the EOA7530.

2.1 Bottom View

The bottom panel of the EOA7530 contains an RJ‐45 port and a Reset button.

‐The RJ‐45 port connects to an Ethernet adapter in a computer you use to configure the EOA7530. For more information, see Chapter 4.

‐The Reset button can be used to reboot the EOA7530 and return the device to its default factory configuration, erasing any overrides you may have made to the device’s default settings. The Reset button is recessed to prevent accidental resets. To reboot the EOA7520, use a flat object such as a pencil to press the Reset button for approximately 10 seconds and then stop pressing the Reset button.

7

Image 8

Contents EOA7530 Table of Contents LAN Setup Page Features Product OverviewBenefits Package Contents System RequirementsHardware Overview Bottom ViewBack Panel Installing the EOA7530 LED Configuring Your Computer for TCP/IP Configuring Microsoft Windows Page Configuring Microsoft Windows Vista Page Configuring Microsoft Windows XP Configuring Microsoft Windows Page Configuring an Apple Macintosh Computer Introducing the Web Configurator Logging in to the Web ConfiguratorBest Practices Wireless Configuration Selecting Operating ModesSelecting Dual Mode for 2.4 GHz and 5 GHz Networks Page Wireless Settings Access Point Mode Dual ModeEssid Apply / Cancel Access Point Mode 5 GHz Access Point Mode 2.4 GHz Client Bridge Mode/Client Router Mode Dual Mode Client Bridge Mode/Client Router Mode 5 GHz 5G Wireless Setting4G Wireless Setting Preferred BssidClient Bridge Mode/Client Router Mode 2.4 GHz Please Choose WDS Bridge ModeOperation Mode 5G Apply / Cancel Default Gateway IP AddressIP Subnet Mask 802.1d Spanning TreeBssid Wlan MAC AddressChannels Data ratesBssid 5.3 Site SurveySsid AP Scan List 5 GHz / 2.4 GHz WMM Wireless Security SettingsWEP Access Point WEP Client Bridge / Client Router WPA Type WPA pre‐shared Key Access PointApply Pre‐shared Key WPA pre‐shared Key Client Bridge / Client RouterPre‐shared Key Type Radius Access Point Mode Only Radius Server Port Radius Server PasswordRadius Server IP Address Wireless Advanced Settings Advanced Settings Access PointAdvanced Settings Client Bridge / Client Router Tx PowerPreamble Type DistanceWireless Access Control List Delete All MAC Address FilteringDelete Selected LAN Setup LAN SettingsCurrent Static Dhcp Table Enable Static Dhcp IPDhcp Info Snmp Disable Snmp SettingsSnmp Enable Static IP Internet SettingsDhcp Dynamic IP PPPoE Point‐to‐Point Protocol over Ethernet MTUStatic IP Address WAN Interface Type Pptp Point‐to‐Point Tunneling ProtocolDynamic IP Address WAN Interface Type Service IP Address Enable Pptp pass throughEnable IPSec pass through Enable L2TP pass throughInformation Status StatusWireless Client List System LogInternet Status Time Zone Settings Management SettingsPassword Settings Diagnosis Save/Reload Settings Remote ControlUpgrade Firmware Restore to Factory Default Settings Backup SettingsRestore Settings RestartNetwork Configuration Example Access Point Mode + Client Bridge ModeClient Router Mode Client BridgeLeft pane, go to Management Operation Mode Access Point Mode EOA7530 Operating ModesClient Bridge Mode Real‐World Configurations Sample Access Point Application‐ Click Apply Sample Access Point and Client Bridge Application Page Page Hardware Specifications Radio Frequency SpecificationsSoftware Features Radio 2 WLAN2Management Environmental and PhysicalProblem Solving Question Answer Factory Default in the Management menuQuestion Answer Contacting Technical SupportChap ESS ID Media Access Control MAC Address Power Over Ethernet PoEProtected Extensible Authentication Protocol Peap Quality of Service QoSWeighted Fair Queuing WFQ Wired Equivalent Privacy WEPWireless Local‐Area Network Wlan Wi‐Fi Protected Access WPAWireless Distribution System WDS WPA2FCC Radiation Exposure Statement Federal Communication Commission Interference StatementImportant Note