EnGenius Technologies EOA7530 manual Federal Communication Commission Interference Statement

Page 83

Appendix D – FCC Interference Statement

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

‐Reorient or relocate the receiving antenna.

‐Increase the separation between the equipment and receiver.

‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

‐Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This transmitter must not be co‐located or operating in conjunction with any other antenna or

transmitter.

Copyright © 2011 ENGENIUS TECHNOLOGIES, INC., All rights reserved.

82

Page 82 Page 84
Image 83
Page 82 Page 84
Contents EOA7530 Table of Contents LAN Setup Page Product Overview FeaturesBenefits System Requirements Package ContentsBottom View Hardware OverviewBack Panel Installing the EOA7530 LED Configuring Your Computer for TCP/IP Configuring Microsoft Windows Page Configuring Microsoft Windows Vista Page Configuring Microsoft Windows XP Configuring Microsoft Windows Page Configuring an Apple Macintosh Computer Logging in to the Web Configurator Introducing the Web ConfiguratorBest Practices Selecting Operating Modes Wireless ConfigurationSelecting Dual Mode for 2.4 GHz and 5 GHz Networks Page Access Point Mode Dual Mode Wireless SettingsEssid Apply / Cancel Access Point Mode 5 GHz Access Point Mode 2.4 GHz Client Bridge Mode/Client Router Mode Dual Mode Preferred Bssid Client Bridge Mode/Client Router Mode 5 GHz5G Wireless Setting 4G Wireless SettingClient Bridge Mode/Client Router Mode 2.4 GHz Please Choose WDS Bridge ModeOperation Mode 5G Apply / Cancel 802.1d Spanning Tree Default GatewayIP Address IP Subnet MaskData rates Bssid Wlan MACAddress ChannelsBssid 5.3 Site SurveySsid AP Scan List 5 GHz / 2.4 GHz WMM Wireless Security SettingsWEP Access Point WEP Client Bridge / Client Router WPA Type WPA pre‐shared Key Access PointApply Pre‐shared Key WPA pre‐shared Key Client Bridge / Client RouterPre‐shared Key Type Radius Access Point Mode Only Radius Server Port Radius Server PasswordRadius Server IP Address Advanced Settings Access Point Wireless Advanced SettingsDistance Advanced Settings Client Bridge / Client RouterTx Power Preamble TypeWireless Access Control List Delete All MAC Address FilteringDelete Selected LAN Settings LAN SetupCurrent Static Dhcp Table Enable Static Dhcp IPDhcp Info Snmp Disable Snmp SettingsSnmp Enable Static IP Internet SettingsDhcp Dynamic IP MTU PPPoE Point‐to‐Point Protocol over EthernetStatic IP Address WAN Interface Type Pptp Point‐to‐Point Tunneling ProtocolDynamic IP Address WAN Interface Type Enable L2TP pass through Service IP AddressEnable Pptp pass through Enable IPSec pass throughStatus Information StatusSystem Log Wireless Client ListInternet Status Time Zone Settings Management SettingsPassword Settings Diagnosis Save/Reload Settings Remote ControlUpgrade Firmware Restart Restore to FactoryDefault Settings Backup Settings Restore SettingsAccess Point Mode + Client Bridge Mode Network Configuration ExampleClient Bridge Client Router ModeLeft pane, go to Management Operation Mode EOA7530 Operating Modes Access Point ModeClient Bridge Mode Sample Access Point Application Real‐World Configurations‐ Click Apply Sample Access Point and Client Bridge Application Page Page Radio Frequency Specifications Hardware SpecificationsRadio 2 WLAN2 Software FeaturesEnvironmental and Physical ManagementFactory Default in the Management menu Problem Solving Question AnswerContacting Technical Support Question AnswerChap ESS ID Quality of Service QoS Media Access Control MAC AddressPower Over Ethernet PoE Protected Extensible Authentication Protocol PeapWi‐Fi Protected Access WPA Weighted Fair Queuing WFQWired Equivalent Privacy WEP Wireless Local‐Area Network WlanWPA2 Wireless Distribution System WDSFCC Radiation Exposure Statement Federal Communication Commission Interference StatementImportant Note

EOA7530 specifications

EnGenius Technologies EOA7530 is a robust, high-performance outdoor access point designed to provide strong, reliable wireless connectivity in various environments. One of its standout features is its dual-band technology, which allows it to operate on both 2.4 GHz and 5 GHz frequencies. This capability enables the EOA7530 to offer a more flexible and efficient networking experience, allowing users to balance load across bands and reduce interference.

Equipped with advanced 802.11ac Wave 2 technology, the EOA7530 supports Multi-User MIMO (MU-MIMO) and beamforming, which enhance performance by allowing multiple clients to connect simultaneously without degrading speed. This is particularly beneficial in high-density areas or environments where many users are vying for network resources.

The EOA7530 is also protected by an IP55-rated enclosure, making it ideal for outdoor installations in challenging weather conditions. This rugged design ensures that the device can withstand dust, water, and even extreme temperatures, delivering uninterrupted service in various climates. Additionally, it is equipped with Power over Ethernet (PoE) capabilities, which simplifies installation by allowing the device to receive both data and power through a single Ethernet cable.

For those looking to extend their coverage, the EOA7530 supports seamless roaming and can be easily integrated into larger EnGenius networks. Users can manage the access point via an intuitive web interface, or utilize the EnGenius Cloud for centralized management of multiple devices, enhancing scalability and ease of use.

Furthermore, the device offers several security features to protect the network against unauthorized access, including WPA3 encryption, guest network capability, and VLAN support. This makes the EOA7530 an excellent choice for businesses looking to enhance security while maintaining user access.

In summary, the EnGenius Technologies EOA7530 is a versatile outdoor access point that combines durability, advanced wireless technology, and robust security features. It is suitable for a variety of applications, from educational campuses to outdoor events, making it an ideal solution for those needing reliable and efficient wireless networking in outdoor environments.
Top Page Image Contents