Enterasys Networks 7G4285-49, 7G4205-72 Recommended Shutdown Procedure Using OFFLINE/RESET Switch

Page 69

Overview of DFE Module Shutdown Procedure

Figure 4-3 OFFLINE/RESET Switch

1

Gb ENET

7G4285-49

À

OFFLINE/

RESET

COM

MGMT CPU

POE

GROUP

SELECT

GROUP

1 1

2 2

3 3

4 4 5

6

1OFFLINE/RESET switch (in similar location on all DFE modules)

Recommended Shutdown Procedure Using OFFLINE/RESET Switch

Caution: Do not pull any DFE module out of an operating chassis before it has completed its shutdown routine.

Precaución: No retire los módulos DFE del chasis en funcionamiento hasta que no se haya terminado con la rutina de apagado.

Before pulling a DFE module out of a chassis,

press or tap on its OFFLINE/RESET switch for less than 1 second.

Its CPU LED changes from solid green to blinking between green and amber, indicating that the DFE module is shutting down. At the end of the DFE module shutdown routine, the CPU LED changes to a 67%/33% sequence of amber/off, respectively, indicating the module is in a halt state. In this time it is safe to restart or remove the DFE module from the chassis.

When a controlled shutdown is initiated from the OFFLINE/RESET switch, you have 60 seconds from the time the CPU starts flashing amber/off until the time the device is automatically restarted.

Note: The only safe time to pull a DFE module out of the chassis is when the CPU LED is blinking amber. Otherwise, system operation will be interrupted.

DFE-Platinum Series Hardware Installation Guide 4-11

Image 69

Contents Enterasys Matrix Page Page Federal Communications Commission FCC Notice Product SafetyIndustry Canada Notice Class a ITE Notice Clase A. Aviso de ITECompatibilidad Electromágnetica EMC Electromagnetic Compatibility EMCElektro- magnetische Kompatibilität EMC Hazardous SubstancesSupplement to Product Instructions Bsmi EMC Statement Taiwan Vcci NoticeDeclaration of Conformity Safety Information Class 1 Laser TransceiversEnterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix a Specifications Figures Xiv Who Should Use This Guide About This GuideHow to Use This Guide Related DocumentsFor Refer to Following conventions are used in this guide Conventions Used in This GuideSupport@enterasys.com Getting HelpOverview of DFE-Platinum Series Module Capabilities Introduction7G4285-49 DFE Module and Interface Options7G4285-49 DFE-Platinum Module 7G4205-72 7G4205-72 DFE-Platinum Module Network Expansion Module NEM Switch Configuration Using WebViewConnectivity ManagementSwitch Configuration Using CLI Commands Secure Networks Policy SupportStandards Compatibility Lanview Diagnostic LEDs Network Requirements 10BASE-T Network Link Aggregation1000BASE-T Network 100BASE-TX Network1000BASE-T Network Network Requirements Installation Contents of DFE Module Carton Quantity Installation Site RequirementRequired Tools Unpacking the DFE ModuleInstalling an Optional Network Expansion Module NEM DFE Module Placement and Installation RulesMatrix E7 Chassis Module Placement Example 1 -1,A Example 2 -1,BExample 3 -1, C Example 4 -1,D Example 5 -1, EExample 6 -1, F Preparing to Install into a Chassis Installing the DFE Modules into a Matrix E7 or N7 Chassis Preparing to Install into a Chassis Preparing to Install into a Chassis Installing the DFE Modules into a Matrix N3 or N5 Chassis Card guides Connecting to the Network Connecting 48 Vdc Power for PoE OperationMaking the UTP Connections Connecting UTP Cables to DFE ModulesConnecting a Twisted Pair Segment with RJ45 Connector RX+ TX+ TX1+ 1 RX1- 2 TX2+ 3 TX3+ 4 RX3- 5 RX2- 6 TX4+ 7 RX4 Verifying PoE Port Status Connecting to COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Parameter Setting Connecting to a VT Series Terminal10 Connecting a VT Series Terminal Connecting to a Modem11 Connecting to a Modem Adapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45RJ45 DB25 Modem Port Adapter Wiring and Signal Diagram Completing the Installation Completing the Installation of a New SystemFirst-Time Log-In Using a Console Port Connection 12 Matrix DFE Startup Screen Example N7 Chassis Enter Logging in with an Administratively-Configured User AccountTroubleshooting Using LanviewAbout the Management Mgmt LED Lanview LEDs on 7G4285-49 Viewing Receive/Transmit Activity on 7G4285-49Lanview LEDs on 7G4205-72 Viewing Receive/Transmit Activity on 7G4205-72Viewing the PoE Port Status Color State Recommended Action Lanview LEDsLED RX/TX Platinum Series Configuration Guide for Troubleshooting ChecklistProblem Possible Cause Recommended Action Troubleshooting ChecklistOverview of DFE Module Shutdown Procedure OFFLINE/RESET Switch Recommended Shutdown Procedure Using OFFLINE/RESET SwitchLast Resort Shutdown Procedure Using OFFLINE/RESET Switch Specifications Table A-1 7G4285-49 Specifications DFE Module SpecificationsProcessors/Memory PhysicalTable A-2 7G4205-72 Specifications COM Port Pinout Assignments Table A-3 COM Port Pin Assignments Signal Name Input/OutputRegulatory Compliance Table A-4 Compliance Standards Regulatory ComplianceMode Switch Settings and Option Installations Setting the Mode Switches Memory Locations and Replacement Procedures Dram Simm Dimm Removing the Safety Cover Gaining Access to Memory ModulesFigure B-3 Removing the Safety Cover Figure B-4 Removing the Optional Network Expansion Module Dram Simm Replacement ProcedureGaining Access to Memory Modules Removing the Dimm Figure B-6 Installing the Dimm Dimm Replacement ProcedureFigure B-7 Removing the Existing Dimm Figure B-8 Installing the Dimm Installing the Network Expansion Module NEMFigure B-9 Installing the Network Expansion Module NEM Reinstalling the Safety Cover Figure B-10 Installing the Safety Cover Page Overview About PoE Power over EthernetProprietary PD Detection Table C-2 PoE Status LED Indications PoE Port Status PoE Port Status LEDsOverview About PoE Power over Ethernet Numerics IndexNEM B-12 installing