Enterasys Networks 7G4285-49, 7G4205-72 manual Contents

Page 13

	Contents
About This Guide
Who Should Use This Guide	xv
How to Use This Guide	xvi
Related Documents	xvi
Conventions Used in This Guide	xvii
Getting Help	xviii
Chapter 1: Introduction
Overview of DFE-Platinum Series Module Capabilities	1-1
DFE Module and Interface Options	1-2
7G4285-49	1-2
7G4205-72	1-4
Network Expansion Module (NEM)	1-6
Connectivity	1-6
7G4285-49	1-6
7G4205-72	1-6
Management	1-6
Switch Configuration Using WebView	1-6
Switch Configuration Using CLI Commands	1-7
Secure Networks Policy Support	1-7
Standards Compatibility	1-7
LANVIEW Diagnostic LEDs	1-8
Chapter 2: Network Requirements
Link Aggregation	2-2
10BASE-T Network	2-2
100BASE-TX Network	2-3
1000BASE-T Network	2-3
Chapter 3: Installation
Installation Site Requirement	3-2
Required Tools	3-2
Unpacking the DFE Module	3-2
Installing an Optional Network Expansion Module (NEM)	3-3
DFE Module Placement and Installation Rules	3-3
Preparing to Install into a Chassis	3-6
Installing the DFE Modules into a Matrix E7 or N7 Chassis	3-7
Installing the DFE Modules into a Matrix N3 or N5 Chassis	3-10
Connecting 48 Vdc Power for PoE Operation	3-12
Connecting to the Network	3-12
Connecting UTP Cables to DFE Modules	3-13
Connecting to COM Port for Local Management	3-18
What Is Needed	3-18

xi

Image 13

Contents Enterasys Matrix Page Page Federal Communications Commission FCC Notice Product SafetyIndustry Canada Notice Class a ITE Notice Clase A. Aviso de ITECompatibilidad Electromágnetica EMC Electromagnetic Compatibility EMCElektro- magnetische Kompatibilität EMC Hazardous SubstancesSupplement to Product Instructions Bsmi EMC Statement Taiwan Vcci NoticeDeclaration of Conformity Safety Information Class 1 Laser TransceiversEnterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix a Specifications Figures Xiv Who Should Use This Guide About This GuideRelated Documents How to Use This GuideFor Refer to Following conventions are used in this guide Conventions Used in This GuideSupport@enterasys.com Getting HelpOverview of DFE-Platinum Series Module Capabilities Introduction7G4285-49 DFE Module and Interface Options7G4285-49 DFE-Platinum Module 7G4205-72 7G4205-72 DFE-Platinum Module Network Expansion Module NEM Switch Configuration Using WebViewConnectivity ManagementSecure Networks Policy Support Switch Configuration Using CLI CommandsStandards Compatibility Lanview Diagnostic LEDs Network Requirements 10BASE-T Network Link Aggregation1000BASE-T Network 100BASE-TX Network1000BASE-T Network Network Requirements Installation Contents of DFE Module Carton Quantity Installation Site RequirementRequired Tools Unpacking the DFE ModuleDFE Module Placement and Installation Rules Installing an Optional Network Expansion Module NEMMatrix E7 Chassis Module Placement Example 2 -1,B Example 1 -1,AExample 3 -1, C Example 5 -1, E Example 4 -1,DExample 6 -1, F Preparing to Install into a Chassis Installing the DFE Modules into a Matrix E7 or N7 Chassis Preparing to Install into a Chassis Preparing to Install into a Chassis Installing the DFE Modules into a Matrix N3 or N5 Chassis Card guides Connecting to the Network Connecting 48 Vdc Power for PoE OperationMaking the UTP Connections Connecting UTP Cables to DFE ModulesConnecting a Twisted Pair Segment with RJ45 Connector RX+ TX+ TX1+ 1 RX1- 2 TX2+ 3 TX3+ 4 RX3- 5 RX2- 6 TX4+ 7 RX4 Verifying PoE Port Status What Is Needed Connecting to COM Port for Local ManagementConnecting to an IBM PC or Compatible Device Parameter Setting Connecting to a VT Series Terminal10 Connecting a VT Series Terminal Connecting to a Modem11 Connecting to a Modem COM Port Adapter Wiring and Signal Diagram RJ45 Adapter Wiring and Signal AssignmentsRJ45 DB25 Modem Port Adapter Wiring and Signal Diagram Completing the Installation of a New System Completing the InstallationFirst-Time Log-In Using a Console Port Connection 12 Matrix DFE Startup Screen Example N7 Chassis Enter Logging in with an Administratively-Configured User AccountUsing Lanview TroubleshootingAbout the Management Mgmt LED Lanview LEDs on 7G4285-49 Viewing Receive/Transmit Activity on 7G4285-49Lanview LEDs on 7G4205-72 Viewing Receive/Transmit Activity on 7G4205-72Viewing the PoE Port Status Color State Recommended Action Lanview LEDsLED RX/TX Platinum Series Configuration Guide for Troubleshooting ChecklistProblem Possible Cause Recommended Action Troubleshooting ChecklistOverview of DFE Module Shutdown Procedure OFFLINE/RESET Switch Recommended Shutdown Procedure Using OFFLINE/RESET SwitchLast Resort Shutdown Procedure Using OFFLINE/RESET Switch Specifications Table A-1 7G4285-49 Specifications DFE Module SpecificationsProcessors/Memory PhysicalTable A-2 7G4205-72 Specifications COM Port Pinout Assignments Table A-3 COM Port Pin Assignments Signal Name Input/OutputRegulatory Compliance Table A-4 Compliance Standards Regulatory ComplianceMode Switch Settings and Option Installations Setting the Mode Switches Memory Locations and Replacement Procedures Dram Simm Dimm Removing the Safety Cover Gaining Access to Memory ModulesFigure B-3 Removing the Safety Cover Figure B-4 Removing the Optional Network Expansion Module Dram Simm Replacement ProcedureGaining Access to Memory Modules Removing the Dimm Figure B-6 Installing the Dimm Dimm Replacement ProcedureFigure B-7 Removing the Existing Dimm Figure B-8 Installing the Dimm Installing the Network Expansion Module NEMFigure B-9 Installing the Network Expansion Module NEM Reinstalling the Safety Cover Figure B-10 Installing the Safety Cover Page Overview About PoE Power over EthernetProprietary PD Detection Table C-2 PoE Status LED Indications PoE Port Status PoE Port Status LEDsOverview About PoE Power over Ethernet Numerics IndexNEM B-12 installing