Enterasys Networks 9034096-02 manual Troubleshooting, Using Lanview, About the Management Mgmt LED

Page 65

4

Troubleshooting

This chapter provides information concerning the following:

For information about...	Refer to page...

Using LANVIEW	4-1

Troubleshooting Checklist	4-5

Matrix DFE-Gold Series Installation Guide	4-6

Recommended Shutdown Procedure Using OFFLINE/RESET Switch	4-7

Last Resort Shutdown Procedure Using OFFLINE/RESET Switch	4-8

Unless otherwise noted, the following information applies to all DFE modules.

Using LANVIEW

The modules use a built‐in visual diagnostic and status monitoring system called LANVIEW. The LANVIEW LEDs (Figure 4‐1) allow quick observation of the network status to aid in diagnosing network problems.

About the Management (MGMT) LED

The MGMT LED (shown in Figure 4‐1) indicates that the module is serving as the Management Module to control the management functions for all DFE‐Gold modules in the chassis. The Management Module handles all IP requests to the chassis IP address, such as PING, Telnet, SNMP, or HTTP. The Management Module also handles the CLI configuration sessions via the console port. Therefore, when you connect to a DFE‐Gold module COM port to configure a module in the chassis, it is handled by the Management Module regardless of the DFE‐Gold module COM port you are connected to.

Matrix DFE-Gold Series Installation Guide 4-1

Image 65

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix a Specifications TroubleshootingAppendix B Mode Switch Bank Settings Optional Installations IndexFigures Tables Important Notice About This GuideWho Should Use This Guide For Refer to How to Use This GuideRelated Documents Following conventions are used in this guide Conventions Used in This GuideConventions Used in This Guide Xvi About This Guide For information about Refer to IntroductionDFE-Gold Modules and Interface Options Overview of DFE Series Capabilities4G4282-49 4G4202-724G4202-72 and 4G4282-49 DFE-Gold Modules 7G-6MGBIC and 7G-6MGBIC-A Gigabit Ethernet Interface Modules Management Switch Configuration Using WebViewConnectivity Secure Networks Policy Support Switch Configuration Using CLI CommandsStandards Compatibility Getting Help Lanview Diagnostic LEDsLink Aggregation Network Requirements1000BASE-SX/LX/ELX Network 10BASE-T Network100BASE-TX Network 1000BASE-T Network 1000BASE-T Network Network Requirements Important Notice InstallationUnpacking the DFE-Gold Module Installing Optional Network Expansion ModulesContents of DFE-Gold Module Carton Quantity Removing the Coverplate Installing the Network Expansion ModuleInstalling the Network Expansion Module Preparation Installing an Optional Mini-GBICMini-GBIC with MT-RJ Connector InstallationMini-GBIC with LC Connector Removing the Mini-GBIC N5 POE Module Placement and RulesExample 2 -6, B Example 1 -6, aExample 3 -6, C Example 4 -6, DInstalling the DFE Module into a Chassis To install the module, refer to ‐1 and proceed as follows Installing Module into Matrix E7 or N7 ChassisCard guides Installing Module into Matrix N1, N3, or N5 Chassis Installing Module into N1, N3, or N5 Chassis only N3 shown Connecting to the NetworkConnecting UTP Cables DFE RX+ TX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting Fiber-Optic Cables to Mini-GBICs 13 Cable Connection to MT-RJ Fiber-Optic Connectors 14 Cable Connection to LC Fiber-Optic Connectors What Is Needed Connecting to COM Port for Local ManagementParameter Setting Connecting to an IBM PC or Compatible Device15 Connecting an IBM PC or Compatible Device Connecting to a VT Series Terminal16 Connecting a VT Series Terminal Connecting to a Modem17 Connecting to a Modem COM Port Adapter Wiring and Signal Diagram RJ45 Adapter Wiring and Signal AssignmentsVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25Modem Port Adapter Wiring and Signal Diagram Completing the InstallationCompleting the Installation of a New System First-Time Log-In Using a Console Port Connection 18 Matrix DFE Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User Account About the Management Mgmt LED TroubleshootingUsing Lanview 4G4282-49 Viewing the Receive and Transmit ActivityColor State Recommended Action LEDAmber Alternating 67% on, 33% and off off. Indicates that a Refer to the Matrix DFE-Gold Series Configuration Troubleshooting ChecklistMatrix DFE-Gold Series Configuration Guide for DFE-Gold Module Shutdown ProcedureOFFLINE/RESET Switch Recommended Shutdown Procedure Using OFFLINE/RESET SwitchLast Resort Shutdown Procedure Using OFFLINE/RESET Switch Table A-1 Specifications SpecificationsDFE-Gold Module Specifications Processors/Memory Ethernet Interface Module SpecificationsTable A-3 Mini-GBIC Input/Output Port Specifications Mini-GBIC Input/Output SpecificationsMGBIC-LC03 Specifications 1000BASE-LX Gigabit Ethernet SpecificationsMGBIC-LC01 / MGBIC-MT01 Specifications 1000BASE-SX Table A-10 MGBIC-08 Optical Specifications MGBIC-LC09 Specifications 1000BASE-LXMGBIC-08 Specifications 1000BASE-ELX Table A-11 MGBIC-08 Operating Range 1550 nm MGBIC-02 Specifications 1000BASE-TTable A-12 MGBIC-02 Specifications Table A-14 Compliance Standards Regulatory Compliance COM Port Pinout AssignmentsRegulatory Compliance Regulatory Compliance Specifications Required Tools Mode Switch Bank Settings Optional InstallationsSetting the Mode Switches Figure B-1 Mode Switch Location on 4G4202-72 and 4G4282-49 Location of Dram Simm and Dimm Memory Modules Memory Locations and Replacement ProceduresRemoving the Dram Simm Dram Simm Replacement ProcedureFigure B-5 Removing the Existing Dram Simm from 4G4282-49 Figure B-6 Installing the Dram Simm on 4G4282-49 Installing the Dram Simm on 4G4282-49Removing the Dimm Dimm Replacement ProcedureFigure B-8 Installing the Dimm on 4G4202-72 or 4G4282-49 Installing the Dimm on 4G4202-72 or 4G4282-49Numerics IndexIndex-2