Enterasys Networks 6H303-48, 4G4282-49, 9034096-02 manual DFE-Gold Module Shutdown Procedure

Page 70

DFE-Gold Module Shutdown Procedure

Table 4-2 Troubleshooting Checklist

(continued)

 

 

 

Problem

Possible Cause

Recommended Action

 

 

 

Port(s) goes into

Loop condition

Verify that Spanning Tree is enabled. Refer to the

standby for no

detected.

Matrix DFE-Gold Series Configuration Guide for

apparent reason.

 

the instructions to set the type of STA.

 

 

Review the network design resolve loops.

 

 

If the problem continues, contact

 

 

Enterasys Networks for technical support.

 

 

 

User parameters

Position of Mode switch

Reenter the lost parameters as necessary. Refer

(IP address, device

(7), Persistent Data

to the Matrix DFE-Gold Series Configuration

and module name,

Reset, was changed

Guide for the instructions to configure the device.

etc.) were lost

sometime before either

If the problem continues, contact

when the module

cycling power or

Enterasys Networks for technical support.

power was cycled,

pressing the OFFLINE/

 

the front panel

RESET switch, causing

 

OFFLINE/RESET

the user-entered

 

switch was

parameters to reset to

 

pressed.

factory default settings.

 

Clear Persistent Data that was set through Local Management.

The module was moved either from slot-to-slot or from chassis-to- chassis.

DFE-Gold Module Shutdown Procedure

Caution: Do not remove a DFE module from an operating chassis system before reading the following information and instructions.

Precaución: Antes de retirar los módulos DFE del chasis en funcionamiento, lea las siguientes instrucciones y la información suministrada.

The DFE‐Gold modules installed in a Matrix E7, Matrix N3, Matrix N5, or Matrix N7 chassis are interdependent and operate under a single IP address as a single, distributed switch system (hardware, databases, and persistent storage). In this operating environment, the DFE‐Gold module must shut down in an orderly fashion to ensure that the other modules in the system and other devices on the network are notified of the impending change. The device(s) can then make intelligent decisions that ensure the stability of the network before the change is made, thereby increasing network availability.

4-6 Troubleshooting

Page 69 Page 71
Image 70
Page 69 Page 71
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix B Mode Switch Bank Settings Optional Installations TroubleshootingAppendix a Specifications IndexFigures Tables Who Should Use This Guide About This GuideImportant Notice Related Documents How to Use This GuideFor Refer to Conventions Used in This Guide Following conventions are used in this guideConventions Used in This Guide Xvi About This Guide Introduction For information about Refer toOverview of DFE Series Capabilities DFE-Gold Modules and Interface Options4G4202-72 4G4282-494G4202-72 and 4G4282-49 DFE-Gold Modules 7G-6MGBIC and 7G-6MGBIC-A Gigabit Ethernet Interface Modules Connectivity Switch Configuration Using WebViewManagement Standards Compatibility Switch Configuration Using CLI CommandsSecure Networks Policy Support Lanview Diagnostic LEDs Getting HelpNetwork Requirements Link Aggregation100BASE-TX Network 10BASE-T Network1000BASE-SX/LX/ELX Network 1000BASE-T Network 1000BASE-T Network Network Requirements Installation Important NoticeContents of DFE-Gold Module Carton Quantity Installing Optional Network Expansion ModulesUnpacking the DFE-Gold Module Installing the Network Expansion Module Removing the CoverplateInstalling the Network Expansion Module Installing an Optional Mini-GBIC PreparationInstallation Mini-GBIC with MT-RJ ConnectorMini-GBIC with LC Connector Removing the Mini-GBIC Module Placement and Rules N5 POEExample 3 -6, C Example 1 -6, aExample 2 -6, B Example 4 -6, DInstalling the DFE Module into a Chassis Installing Module into Matrix E7 or N7 Chassis To install the module, refer to ‐1 and proceed as followsCard guides Installing Module into Matrix N1, N3, or N5 Chassis Connecting to the Network Installing Module into N1, N3, or N5 Chassis only N3 shownConnecting UTP Cables DFE RX+ TX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting Fiber-Optic Cables to Mini-GBICs 13 Cable Connection to MT-RJ Fiber-Optic Connectors 14 Cable Connection to LC Fiber-Optic Connectors Connecting to COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Parameter SettingConnecting to a VT Series Terminal 15 Connecting an IBM PC or Compatible DeviceConnecting to a Modem 16 Connecting a VT Series Terminal17 Connecting to a Modem VT Series Port Adapter Wiring and Signal Diagram Adapter Wiring and Signal AssignmentsCOM Port Adapter Wiring and Signal Diagram RJ45 RJ45 DB25Completing the Installation of a New System Completing the InstallationModem Port Adapter Wiring and Signal Diagram First-Time Log-In Using a Console Port Connection 18 Matrix DFE Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User Account Using Lanview TroubleshootingAbout the Management Mgmt LED Viewing the Receive and Transmit Activity 4G4282-49LED Color State Recommended ActionAmber Alternating 67% on, 33% and off off. Indicates that a Troubleshooting Checklist Refer to the Matrix DFE-Gold Series ConfigurationDFE-Gold Module Shutdown Procedure Matrix DFE-Gold Series Configuration Guide forRecommended Shutdown Procedure Using OFFLINE/RESET Switch OFFLINE/RESET SwitchLast Resort Shutdown Procedure Using OFFLINE/RESET Switch DFE-Gold Module Specifications SpecificationsTable A-1 Specifications Ethernet Interface Module Specifications Processors/MemoryMini-GBIC Input/Output Specifications Table A-3 Mini-GBIC Input/Output Port SpecificationsMGBIC-LC01 / MGBIC-MT01 Specifications 1000BASE-SX Gigabit Ethernet SpecificationsMGBIC-LC03 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELX MGBIC-LC09 Specifications 1000BASE-LXTable A-10 MGBIC-08 Optical Specifications Table A-12 MGBIC-02 Specifications MGBIC-02 Specifications 1000BASE-TTable A-11 MGBIC-08 Operating Range 1550 nm Regulatory Compliance COM Port Pinout AssignmentsTable A-14 Compliance Standards Regulatory Compliance Regulatory Compliance Specifications Setting the Mode Switches Mode Switch Bank Settings Optional InstallationsRequired Tools Figure B-1 Mode Switch Location on 4G4202-72 and 4G4282-49 Memory Locations and Replacement Procedures Location of Dram Simm and Dimm Memory ModulesDram Simm Replacement Procedure Removing the Dram SimmFigure B-5 Removing the Existing Dram Simm from 4G4282-49 Installing the Dram Simm on 4G4282-49 Figure B-6 Installing the Dram Simm on 4G4282-49Dimm Replacement Procedure Removing the DimmInstalling the Dimm on 4G4202-72 or 4G4282-49 Figure B-8 Installing the Dimm on 4G4202-72 or 4G4282-49Index NumericsIndex-2
Top Page Image Contents