Lyngdorf Audio TDA 2200 owner manual Technical Specifications a. Audio, Parameter, Value

Page 39
17. Technical Specifications a. Audio

17. Technical Specifications a. Audio

Parameter

Value

Note

Balanced input connectors

3 pin XLR, gold-plated.

Case=Gnd, Pin1=Gnd,

 

 

Pin2=Hot(+), Pin3=Cold(-)

Balanced input impedance

10kOhm

AC-coupled.

Unbalanced input connectors

RCA (phono) jack, gold-plated. Case=Gnd, Tip=Hot(+)

Unbalanced input impedance

10kOhm

AC-coupled

DAC Out impedance

75 Ohm

Gain According to volume

 

 

control setting. 89 dB = 0 dB

 

 

with sensitivity normal and rel.

 

 

volume 0 dB

Input sensitivity

4.4V (2.2V with high sens.)

200W/8ohms/89 dB Volume

Power Supply Variation

26dB

65V to 3.3V dep. On Volume

Output connectors

4 insulated binding posts, gold-Will accept bare wire ends of

 

plated.

up to 5 mm diameter.

Output power, 8ohms

2*200W

1KHz, 0.1% THD+N

Output power, 4ohms

2*375W

1KHz, 0.1% THD+N

Nominal load impedance

4 Ohms-8 Ohms

It is safe to operate the

 

 

amplifier with no load.

Frequency response

0.3Hz-33KHz

-3dB points, 8ohms load.

Frequency response

-0dB/+0.2dB

20Hz-20KHz, 8ohms load

Frequency response

-0.2dB/+0dB

20Hz-20KHz, 4ohms load

Output impedance

0.035 Ohms

20Hz-1KHz

Output impedance

0.4 Ohms

20KHz

THD+N, 1W/8ohms

0.015%

A-wgt.

THD+N, 1W/4ohms

0.02%

A-wgt.

THD+N, 100W/8ohms

0.008%

A-wgt.

THD+N, 180W/8ohms

0.01%

A-wgt.

THD+N, 375W/4ohms

0.07%

A-wgt.

S/N ratio

107dB

A-wgt. Ref. 200W/8ohms.

Dynamic range

133 dB

A-wgt. Ref. 200W/8ohms.

Channel separation

90dB

1KHz, 200W/8ohms.

Peak output current

±40A

 

Output common mode voltage

Max 33V DC

Ref. Ground. The amplifier can

 

 

not be used in bridged mono

 

 

mode.

Output DC voltage

±5 mV

 

 

 

 

 

 

 

 

 

 

All audio measurements, except frequency response, are measured with a 20KHz low- pass filter in accordance with AES-17.

39

Image 39
Contents RoomPerfect Page Table of Contents RoomPerfect Advanced Menu 1. WARNINGS a. Explanation of graphical symbolsi.Exclamation symbol ii.Lightning symbolb. Important safety instructions 2. Unpacking the TDA a. Accessoriesb. Operating Voltage 3.Product Registration4. Introduction 5. Front Panel a. ControlsFig 1 TDA 2200 front panel b. Display Indicators Fig 2 TDA 2200 rear panel 6. Rear Panel7. Remote Control 8. Menu System a. RoomPerfect b. Voicingc. Crossover d. Delay f. Communication e. ADC Level - Otionalh. Remote Control g. Trigger Set-upi. Display j. Volume k. Advanced set-up 9. RoomPerfect a. The Guided Set-up- a Quick Guide Fig 3 Measurement of main listening position b. Setting the measurement volume levelPage c. Focus Measurement d. Room Measurements e.Adding more room measurements f.Calculation of Focus 1 and Global Filters 10. RoomPerfect Advanced Menu a. Selected Positionb. Adding a New Focus Position Press enter to continue c. Adding a New Room Position e. RoomCorrection Index d. RoomKnowledge Index11.Daily Use of RoomPerfect a. Global Listeningb. Focus Listening 12. RoomPerfect Troubleshooting b. Fault - No signala. No microphone connected d. Fault - Low signal c. Fault - Signal clipping13. Software Fig 5 Software Upgrade Tool14. Connectors a. Mains Connectorb. Loudspeaker Connectors a. Balanced inputs 16. Cleaning and Maintenancec. Trigger connector 15. Optional AD Converter Board17. Technical Specifications a. Audio ParameterValue e. Mechanical b. Protectionc. Mains d. Trigger18. Technical Assistance a. SupportLyngdorf Audio a. Menu Tree 19. AppendixDesharp1 b. Voicing CurvesSoft Open