Lyngdorf Audio TDA 2200 owner manual b. Voicing Curves, Soft, Open, Desharp1

Page 43

b. Voicing Curves

b. Voicing Curves

Soft 1

Magnitude Response: Soft 1

	6
	4
(dB)	2
(dB)
Magnitude	0
	-2
	-4
	-6
	10 Hz	100 Hz	1kHz	10kHz

Frequency (Hz)

Open 1

Magnitude Response: Open 1

		6
		4
	(dB)	2
	(dB)
	Magnitude	0
	Magnitude	-2
		-2
		-4
		-6

10 Hz	100 Hz	1kHz	10kHz
	Frequency (Hz)

Soft 2

Magnitude Response: Soft 2

	6
	4
(dB)	2
(dB)
Magnitude	0
	-2
	-4
	-6
	10 Hz	100 Hz	1kHz	10kHz

Frequency (Hz)

Open 2

Magnitude Response: Open 2

		6
		4
	(dB)	2
	(dB)
	Magnitude	0
	Magnitude	-2
		-2
		-4
		-6

10 Hz	100 Hz	1kHz	10kHz
	Frequency (Hz)

Desharp1

Magnitude Response: Desharp 1

	6
	4
(dB)	2
(dB)
Magnitude	0
	0
	-2
	-4
	-6
	10 Hz	100 Hz	1kHz	10kHz

Frequency (Hz)

Desharp 2

Magnitude Response: Desharp 2

	6
	4
(dB)	2
(dB)
Magnitude	0
	-2
	-4
	-6
	10 Hz	100 Hz	1kHz	10kHz

Frequency (Hz)

43

Image 43

Contents RoomPerfect Page Table of Contents RoomPerfect Advanced Menu 1. WARNINGS a. Explanation of graphical symbolsi.Exclamation symbol ii.Lightning symbolb. Important safety instructions 2. Unpacking the TDA a. Accessoriesb. Operating Voltage 3.Product Registration4. Introduction a. Controls 5. Front PanelFig 1 TDA 2200 front panel b. Display Indicators Fig 2 TDA 2200 rear panel 6. Rear Panel7. Remote Control 8. Menu System b. Voicing a. RoomPerfectc. Crossover d. Delay f. Communication e. ADC Level - Otionalg. Trigger Set-up h. Remote Controli. Display j. Volume k. Advanced set-up 9. RoomPerfect a. The Guided Set-up- a Quick Guide Fig 3 Measurement of main listening position b. Setting the measurement volume levelPage c. Focus Measurement d. Room Measurements e.Adding more room measurements f.Calculation of Focus 1 and Global Filters a. Selected Position 10. RoomPerfect Advanced Menub. Adding a New Focus Position Press enter to continue c. Adding a New Room Position e. RoomCorrection Index d. RoomKnowledge Indexa. Global Listening 11.Daily Use of RoomPerfectb. Focus Listening b. Fault - No signal 12. RoomPerfect Troubleshootinga. No microphone connected d. Fault - Low signal c. Fault - Signal clipping13. Software Fig 5 Software Upgrade Toola. Mains Connector 14. Connectorsb. Loudspeaker Connectors a. Balanced inputs 16. Cleaning and Maintenancec. Trigger connector 15. Optional AD Converter BoardParameter 17. Technical Specifications a. AudioValue e. Mechanical b. Protectionc. Mains d. Triggera. Support 18. Technical AssistanceLyngdorf Audio a. Menu Tree 19. AppendixDesharp1 b. Voicing CurvesSoft Open