Lyngdorf Audio TDA 2200 owner manual b. Protection, c. Mains, d. Trigger, e. Mechanical

Page 40
b. Protection

b. Protection

Parameter

Value

Note

Grounding

Mains earth, chassis and audio

 

 

ground are connected

 

 

internally.

 

Output short circuit current

±40A

 

Output DC voltage

±5V @ <0.1Hz

 

Over temperature

All heat sinks and mains-

Auto resetting thermal fuse in

 

transformer.

mains transformer.

c. Mains

Parameter

Value

Note

Mains input connector

IEC 320 cold type

Mains lead supplied.

Mains voltage range

100-120V AC, 50–60Hz

115V version

Mains voltage range

200-240V AC, 50-60Hz

230V version

Internal mains fuse

8 Amp / 0.25A

115V version

Internal mains fuse

4 Amp / 0.1A

230V version

Power consumption

1.5 W

STANDBY mode.

Power consumption

35 W

OPERATE mode, no output.

Power consumption

116 W

2*37.5W/4ohms.

Power consumption

820 W

2*300W/4ohms.

d. Trigger

Parameter

Value

Note

TRIGGER OUT connector

3.5mm (1/8") mono jack

Case=Gnd, Tip=Input

TRIGGER OUT Voltage

12V DC

Short circuit protected

e. Mechanical

Parameter

Value

Note

Width

450mm (17.72")

 

Depth

435mm (13.39")

Excluding loudspeaker

 

 

connectors (over wheel)

Depth

455mm (14.21")

Including loudspeaker

 

 

connectors (over wheel.

Height

88.8mm (3.5")

Excluding feet.

Height

100.6mm (3.96")

Including feet.

Net weight

18.0Kg (37lb.)

 

Shipping weight

20.0Kg (41lb.)

 

40

Image 40
Contents RoomPerfect Page Table of Contents RoomPerfect Advanced Menu a. Explanation of graphical symbols i.Exclamation symbolii.Lightning symbol 1. WARNINGSb. Important safety instructions a. Accessories 2. Unpacking the TDA3.Product Registration b. Operating Voltage4. Introduction a. Controls 5. Front PanelFig 1 TDA 2200 front panel b. Display Indicators 6. Rear Panel Fig 2 TDA 2200 rear panel7. Remote Control 8. Menu System b. Voicing a. RoomPerfectc. Crossover d. Delay e. ADC Level - Otional f. Communicationg. Trigger Set-up h. Remote Controli. Display j. Volume k. Advanced set-up 9. RoomPerfect a. The Guided Set-up- a Quick Guide b. Setting the measurement volume level Fig 3 Measurement of main listening positionPage c. Focus Measurement d. Room Measurements e.Adding more room measurements f.Calculation of Focus 1 and Global Filters a. Selected Position 10. RoomPerfect Advanced Menub. Adding a New Focus Position Press enter to continue c. Adding a New Room Position d. RoomKnowledge Index e. RoomCorrection Indexa. Global Listening 11.Daily Use of RoomPerfectb. Focus Listening b. Fault - No signal 12. RoomPerfect Troubleshootinga. No microphone connected c. Fault - Signal clipping d. Fault - Low signalFig 5 Software Upgrade Tool 13. Softwarea. Mains Connector 14. Connectorsb. Loudspeaker Connectors 16. Cleaning and Maintenance c. Trigger connector15. Optional AD Converter Board a. Balanced inputsParameter 17. Technical Specifications a. AudioValue b. Protection c. Mainsd. Trigger e. Mechanicala. Support 18. Technical AssistanceLyngdorf Audio 19. Appendix a. Menu Treeb. Voicing Curves SoftOpen Desharp1