Cypress CY8C23533, CY8C23433 manual DC Operational Amplifier Specifications, Psrroa

CY8C23433, CY8C23533

DC Operational Amplifier Specifications

The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V and 3.3V at 25°C and are for design guidance only.

The Operational Amplifier is a component of both the Analog Continuous Time PSoC blocks and the Analog Switched Cap PSoC blocks. The guaranteed specifications are measured in the Analog Continuous Time PSoC block. Typical parameters apply to 5V at 25°C and are for design guidance only.

Table 13. 5V DC Operational Amplifier Specifications

Symbol	Description	Min	Typ	Max	Units	Notes
VOSOA	Input Offset Voltage (absolute value)	–	1.6	10	mV
	Power = Low, Opamp Bias = High
	Power = Medium, Opamp Bias = High	–	1.3	8	mV
	Power = High, Opamp Bias = High	–	1.2	7.5	mV
TCVOSOA	Average Input Offset Voltage Drift	–	7.0	35.0	μV/°C
IEBOA	Input Leakage Current (Port 0 Analog Pins)	–	20	–	pA	Gross tested to 1 μA
CINOA	Input Capacitance (Port 0 Analog Pins)	–	4.5	9.5	pF	Package and pin dependent.
						Temp = 25°C
VCMOA	Common Mode Voltage Range	0.0	–	Vdd	V	The common-mode input
	Common Mode Voltage Range (high power or high	0.5	–	Vdd - 0.5		voltage range is measured
	opamp bias)					through an analog output
						buffer. The specification
						includes the limitations
						imposed by the character-
						istics of the analog output
						buffer.
GOLOA	Open Loop Gain	60	–	–	dB	Specification is applicable at
	Power = Low, Opamp Bias = High					high power. For all other bias
	Power = Medium, Opamp Bias = High	60				modes (except high power,
	Power = High, Opamp Bias = High	80				high opamp bias), minimum is
						60 dB.
VOHIGHOA	High Output Voltage Swing (internal signals)	Vdd - 0.2	–	–	V
	Power = Low, Opamp Bias = High
	Power = Medium, Opamp Bias = High	Vdd - 0.2	–	–	V
	Power = High, Opamp Bias = High	Vdd - 0.5	–	–	V
VOLOWOA	Low Output Voltage Swing (internal signals)	–	–	0.2	V
	Power = Low, Opamp Bias = High
	Power = Medium, Opamp Bias = High	–	–	0.2	V
	Power = High, Opamp Bias = High	–	–	0.5	V
ISOA	Supply Current (including associated AGND buffer)	–	300	400	μA
	Power = Low, Opamp Bias = High
	Power = Medium, Opamp Bias = Low	–	600	800	μA
	Power = Medium, Opamp Bias = High	–	1200	1600	μA
	Power = High, Opamp Bias = Low	–	2400	3200	μA
	Power = High, Opamp Bias = High	–	4600	6400	μA
PSRROA	Supply Voltage Rejection Ratio	52	80	–	dB	Vss ≤ VIN ≤ (Vdd - 2.25) or
						(Vdd - 1.25V) ≤ VIN ≤ Vdd

Document Number: 001-44369 Rev. *B Page 18 of 37

[+] Feedback