Cypress CY8C23433, CY8C23533 manual DC Programming Specifications

Page 23

CY8C23433, CY8C23533

DC Programming Specifications

The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V and 3.3V at 25°C and are for design guidance only.

Table 22. DC Programming Specifications

Symbol

Description

Min

Typ

Max

Units

Notes

VddIWRITE

Supply Voltage for Flash Write Operations

2.7

–

–

V

 

IDDP

Supply Current During Programming or Verify

–

5

25

mA

 

VILP

Input Low Voltage During Programming or

–

–

0.8

V

 

 

Verify

 

 

 

 

 

VIHP

Input High Voltage During Programming or

2.1

–

–

V

 

 

Verify

 

 

 

 

 

IILP

Input Current when Applying Vilp to P1[0] or

–

–

0.2

mA

Driving internal pull down

 

P1[1] During Programming or Verify

 

 

 

 

resistor

IIHP

Input Current when Applying Vihp to P1[0] or

–

–

1.5

mA

Driving internal pull down

 

P1[1] During Programming or Verify

 

 

 

 

resistor

VOLV

Output Low Voltage During Programming or

–

–

Vss + 0.75

V

 

 

Verify

 

 

 

 

 

VOHV

Output High Voltage During Programming or

Vdd - 1.0

–

Vdd

V

 

 

Verify

 

 

 

 

 

FlashENPB

Flash Endurance (per block)

50,000

–

–

–

Erase/write cycles per block

FlashENT

Flash Endurance (total)[11]

1,800,000

–

–

–

Erase/write cycles

FlashDR

Flash Data Retention

10

–

–

Years

 

Note

11.A maximum of 36 x 50,000 block endurance cycles is allowed. This may be balanced between operations on 36x1 blocks of 50,000 maximum cycles each, 36x2 blocks of 25,000 maximum cycles each, or 36x4 blocks of 12,500 maximum cycles each (to limit the total number of cycles to 36x50,000 and that no single block ever sees more than 50,000 cycles).

For the full industrial range, the user must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing. Refer to 0xthe Flash APIs Application Note AN2015 at http://www.cypress.com under Application Notes for more information.

Document Number: 001-44369 Rev. *B

Page 23 of 37

[+] Feedback

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Logic Block Diagram FeaturesPSoC Core PSoC Functional OverviewDigital System Analog System Analog System Block DiagramDevelopment Kits Technical Training Modules PSoC Device CharacteristicsGetting Started Additional System ResourcesDesign Browser Development ToolsPSoC Designer Software Subsystems Device EditorDebugger Designing with User ModulesHardware Tools Application EditorAcronyms Used Document ConventionsUnits of Measure Numeric NamingSDA, ISSP-SDATA PinoutsPin Part Pinout SCL, ISSP-SCLKI2C SDA Pin Definitions 28-Pin Ssop Number Name DescriptionPin I2C SCLAbbreviations Used Register ReferenceRegister Conventions Register Mapping TablesRegister Map Bank 0 Table User Space Name Addr 1,Hex Access Register Map Bank 1 Table Configuration SpaceACB01CR0 RDI0RO0 ACB01CR1 RDI0RO1 Units of Measure Electrical SpecificationsAbsolute Maximum Ratings Operating TemperatureAbsolute Maximum Ratings Symbol Description Min Typ Units Operating Temperature Symbol Description Min Typ Max UnitsDC Chip-Level Specifications DC Electrical CharacteristicsDC General Purpose IO Specifications Psrroa DC Operational Amplifier SpecificationsLPC voltage offset Document Number 001-44369 Rev. *B DC Low Power Comparator SpecificationsLow power comparator LPC reference voltage Vdd Range LPC supply currentPsrrob DC Analog Output Buffer SpecificationsDC Analog Reference Specifications DC POR and LVD Specifications DC Analog PSoC Block SpecificationsDC Programming Specifications DNL SAR8 ADC DC SpecificationsINL AC Chip-Level Specifications AC Electrical Characteristics32K Select EnablePLL GainBwoa AC General Purpose IO SpecificationsAC Operational Amplifier Specifications CY8C23433, CY8C23533 Typical Agnd Noise with P24 Bypass AC Digital Block Specifications AC Low Power Comparator SpecificationsBwob AC Analog Output Buffer SpecificationsLarge Signal Bandwidth, 1Vpp, 3 dB BW, 100 pF Load KHz Power = Low Power = HighSAR8 ADC AC Specifications AC External Clock SpecificationsAC Programming Specifications AC I2C Specifications Pin 5x5 mm QFN Packaging InformationThermal Impedances Capacitance on Crystal PinsSolder Reflow Peak Temperature Typical Package Capacitance on Crystal PinsOrdering Information Orig. Submission Description of Change Date Sales, Solutions, and Legal InformationWorldwide Sales and Design Support Products PSoC Solutions Document History
Top Page Image Contents