Mark Levinson 532 owner manual Rear Panel, Mark Levinson Status LED

Page 12

8

Audio

Input

Mark Levinson

Status LED

Indicates the operating state of the Nº532 and provides basic diagnostic information if a fault condition occurs. The table below identifies the basic behavior of the Status LED.

LED Behavior

Description

 

 

Fully lit

Indicates that the amplifier is powered on.

 

 

Slowly blinking

Indicates that the amplifier is in Standby mode.

 

 

Dimly lit

Indicates that the amplifier is in Power Save mode.

 

 

Not lit

Indicates that the amplifier is powered off.

 

 

Refer to the “Troubleshooting” section in the back of the manual for a description of the Status LED behavior when a fault is detected.

Rear Panel

The Nº532 has two independent audio channels, isolated from each other and from the control circuitry. This isolated design results in two “piers”, each containing identical circuitry for a single audio channel. The control circuitry resides in the center of the amplifier, isolated from each audio channel. The resulting rear panel, as shown below, is actually three separate parts: the center part contains all of the control and power connections, while the left and right panels each contain the connectors for each audio channel.

Ethernet

Link2

Power Save

Trigger

Audio

Port

Ports

Mode Switch

Input/Output

Input

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Loudspeaker

AC Input

Loudspeaker

Binding Posts

 

 

Binding Posts

Image 12
Contents No532 Power Amplifier FCC Notice Important Safety Instructions IiiSafety Terms & Symbols Documentation ConventionsMark Levinson Table of Contents Introduction Product DescriptionWhat’s in the Box QuantityInstallation Considerations PlacementProduct Registration UnpackingPower Requirements Operating States Status LED Standby Button Power Power Button Front PanelStandby Button Rear Panel Mark Levinson Status LEDAudio Channel Inputs Loudspeaker Binding PostsSingle-Ended Inputs Balanced InputsTrigger Input Output Power Save Mode Switch Network Setup Link2 PortsEthernet Port AC Input Material Requirements Computer Connecting the Cables To Connect Using a Router O532 Computer Internal WebTo Connect Without a Router Crossover Cable No532 ComputerNetwork Setup Parameters Connecting With Dhcp Recommended Setting Up Computer Network Setup for Windows XPTo change the Host Name of the Nº532 Network Setup for Windows Connecting With Static IP Addressing To change the Host Name of the Nº532 Direct Connection Masters and Slaves Connecting Devices ML NetDiscovering Slaves Status Reporting Fault Reporting Link2 ML Net and Link2Troubleshooting No Power No OutputCan’t Assign in ML Net Mark Levinson Fault Protection ML Net Fault ConditionsRestoring Factory Defaults Care & MaintenanceSpecifications Input & Output ConnectorsDeclaration of Conformity Manufacturer

532 specifications

The Mark Levinson No. 532 is a high-performance power amplifier that exemplifies the best in audio technology. Renowned for delivering unparalleled sound quality, the No. 532 combines advanced engineering with state-of-the-art components to create an audio experience that meets the demands of audiophiles and professionals alike.

One of the standout features of the No. 532 is its robust power output. Properly equipped to deliver up to 300 watts per channel into 8 ohms, and even more into lower impedances, this amplifier ensures that it can drive a wide range of speakers with ease. This impressive power performance is complemented by its class AB topology, which strikes an optimal balance between efficiency and sound fidelity, providing listeners with rich, full-bodied audio reproduction across all frequencies.

The No. 532 showcases Mark Levinson's hallmark meticulous craftsmanship. The unit is built using premium-grade materials, featuring a solid chassis that minimizes resonance and external interference. The elegantly designed exterior houses advanced circuitry, including a fully balanced design that reduces noise and distortion, allowing the amplifier to deliver crystal-clear sound.

Incorporating proprietary technologies, the No. 532 employs the Mark Levinson's custom-built output devices and a sophisticated power supply that guarantees steady performance and dynamic audio reproduction at any volume level. Additionally, the amplifier features an intelligence-driven thermal management system, ensuring optimal performance while preventing overheating during extended use.

User-friendly features enhance the listening experience further. The No. 532 includes multiple inputs, facilitating seamless integration into various audio systems. It also has an intuitive interface that allows users to monitor performance and make adjustments with ease.

Finally, the Mark Levinson No. 532 amplifier is not just about raw power; it excels in sound transparency and detail. It delivers an expansive soundstage, allowing listeners to experience audio as intended by the creators, capturing the subtleties of every instrument and vocal nuance. This makes the No. 532 a cornerstone choice for those committed to experiencing music in its most accurate form.

In conclusion, the Mark Levinson No. 532 stands out for its superior build quality, exceptional power capabilities, and advanced technological features, ultimately providing an audio performance that is both profound and engaging. Whether for personal enjoyment or professional use, this amplifier is designed for those who demand the finest in high-fidelity audio.