Multitech MT5600BA, MT5600BL manual Basic Options

Page 23
Basic Options

Chapter 3 - Using the Front Panel

Basic Options

The following screens are used to configure the modem’s basic operating conditions.

ONLINE OPTIONS. The following screens are used to configure the online operation of the modem:

LINE TYPE OPTIONS. Use the Æ and Enter buttons to select from the following line types: dial-up (PSTN), two-wire leased line originate or answer, and four-wire leased line originate or answer.

ERROR CORRECTION OPTIONS. Use the Æ and Enter but- tons to turn error correction on or off, or to select automatic error correction. Same as the &E0, &E1, and &E2 commands.

FLOW CONTROL OPTIONS. Use the Æ and Enter buttons to select no flow control, hardware flow control, or software flow control. Same as the &E3, &E4, and &E5 commands.

DIALING OPTIONS. The following screens are used to configure dialing options or to dial manually.

TONE/PULSE. Use the Æ and Enter buttons to select between DTMF tone dialing and pulse dialing. Same as the T and P com- mands.

BLIND/SMART DIAL OPTIONS. Use the Æ and Enter buttons to select blind dialing, in which the modem sends the OK, CON- NECT, RING, NO CARRIER, ERROR and NO ANSWER mes- sages to the computer and does not look for a dial tone or busy signal, or smart dialing, in which the modem sends all messages to the computer, including NO DIALTONE and BUSY. Same as the X0 and X4 commands.

DIAL NUMBER. Use the front panel buttons to enter a phone number and dial it. To scroll through a list of digits and charac- ters, press the ÇÅ and È buttons. To go to the next position, press the Æ button. To back up or to exit without dialing, press the Æ button several times. To dial the number, press the Enter button. Same as the D command.

DTR DIALING. Use the Æ and Enter buttons to enable or dis- able DTR dialing. DTR dialing is popular in synchronous applica- tions. In DTR dialing, the modem automatically dials the number stored in memory location 0 when it detects a high DTR (Data Terminal Ready) signal on the RS-232 interface. The DTR signal must remain high for the duration of the call. To store the DTR dialing number, use the &Z0= command or the ENTER PHONE #0 menu option.

Note: Plug and Play does not function if DTR dialing is enabled. DTR is used during Plug and Play, and DTR dialing interferes with it.

Multi-Tech Systems, Inc. MT5600BA/BL Series User Guide (S000276E)

23

 

Page 22 Page 24
Image 23
Page 22 Page 24
Contents MT5600BA-V.92 MT5600BA-V.90 MT5600BL-V.90 MT5600BA/BL SeriesData/Fax Modem User Guide Patents MultiModemII User GuideRecord of Revisions TrademarksMultiModemII User Guide Table of ContentsTable of Contents None of the Indicators Light Product Description Chapter 1 - Description and FeaturesAbout AT Commands FeaturesSafety Warnings Connect the Modem to the Telephone Line Dialup Connection Connect theTwo-Wire Leased LineStep 1 - Connect the Modem to Your System Connect the Modem to Your PCConnect the Phone to the Modem Optional Connect the Four-Wire Leased LineConnect the Modem to the AC Power Outlet Power-On TestRemoving an Old Modem Driver Step 2 - Install the Modem DriverInstalling the Modem Driver for Windows 98/Me/2000 XP Installing the Modem Driver for Windows NTMT5600BA-V.92 Only Step 3 - Setting Your Country or Region CodeUsing the LCD Panel Using the Global WizardHow to Verify the Code Step 4 - Install PhoneToolsUsing AT Commands How to Change the Country/Region CodeLED Indicators Chapter 3 - Using the Front PanelModem Configuration Menu Structure Liquid Crystal Display LCDOption Selection Branches Menu OverviewTrunks LimbsLimbs Twigs Status TrunkTwigs Basic Options TrunkLimbs BranchesContinued from previous page Basic Options Trunk, continuedAdvanced Options Trunk Advanced Options Trunk, continued Limb Remote Configuration Options TrunkDiagnostic Options Trunk Caller ID Options Trunk Phone Number Memory Options TrunkStatus Menu OptionsBasic Options ASYNC, NORM? Normal asynchronous transmission using the Advanced Options VIEW S-REGISTER SETTINGS. Use the Æ, È, ÇÅ, and Enter buttons to select the number of the S-register whose value you want displayed. To scroll through a list of digits, press the ÇÅ and È buttons. To go to the next position, press the Æ button. To back up or to exit without saving, press the Æ button several times. To display the value, press the Enter button. Same as the Sr? command Phone Number Memory Options Remote Configuration OptionsDiagnostic Options Caller ID Options Chapter 4 - Leased Line Operation Two-Wire SetupFour-Wire Setup Dial Backup and Leased Line Restoral Setup Dial Backup and Leased-Line Restoral10. Press the Æ button to go to the next digit in the number Changing the Remote Configuration Password Chapter 5 - Remote ConfigurationBasic Procedure SetupChanging the Remote Escape Character Turning Callback Security On and Off Setup ProceduresAT Command Method Chapter 6 - Callback SecurityFront Panel Method Assigning Callback PasswordsAT Command Method Front Panel Method Assigning Callback Phone NumbersCalling Procedure Command #CBP y= x Store Callback Password Callback Security CommandsCommand #DBn Callback Enable/Disable Command #CBN y= - x Store Callback NumberCallback Assignments Form LocationPasswordPhone NumberNone of the Indicators Light Chapter 7 - TroubleshootingThe Modem Does Not Respond to Commands The Modem Cannot Connect When Dialing The Modem Disconnects While Online Data Is Being Lost The Modem Cannot Connect When AnsweringFile Transfer Is Slower Than It Should Be Fax and Data Software Can’t Run at the Same Time There Are Garbage Characters on the MonitorThe Modem Doesn’t Work with Caller ID FCC Part 68 Telecom Appendix A - Regulatory ComplianceCanadian Limitations Notice Fax Branding StatementNew Zealand Telecom Warning Notice EMC, Safety, and R&TTE Directive ComplianceInternational Modem Restrictions South African Notice Appendix B - Technical Specifications loop Step 1 - Identify the Modem Firmware Upgrade OverviewAppendix D - Upgrading the Firmware IntroductionStep 2 - Identify the Current Firmware Version Step 3 - Download the Upgrade FileStep 4 - Extract the Upgrade Files Step 5 - Clear Your Stored Paramenters Step 6 - Upgrade the Modem’s FirmwareStep 7 - Restore Your Parameters Installation Appendix E - Installing a Modem Under LinuxUsing the Terminal Program Minicom to Verify Operation Standard Linux Serial Port Definitions3. Select Dialup Configuration Tool Using the Modem to Call the InternetCalling the ISP Answering CallsRS-232 Pin Descriptions Appendix F - Pin DescriptionsAppendix F - Pin Descriptions RS-232 Cable PinoutsHSKi CTS HSKo RTS Leased Line PinoutsDTE Mini-DIN 8-pin connector DCE DB-25 connectorIndex
Top Page Image Contents