Multitech MT5600BA EMC, Safety, and R&TTE Directive Compliance, International Modem Restrictions

Page 49
EMC, Safety, and R&TTE Directive Compliance

Appendix A - Regulatory Compliance

EMC, Safety, and R&TTE Directive Compliance

The CE mark is affixed to this product to confirm compliance with the following European Community Directives:

Council Directive 2004/108/EC of 15 December 2004 on the approximation of the laws of Member States relating to electromagnetic compatibility;

and

Council Directive 2006/95/EC of 12 December 2006 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits;

and

Council Directive 1999/5/EC of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity.

International Modem Restrictions

Some dialing and answering defaults and restrictions may vary for international modems. Changing settings may cause a modem to become non-compliant with national telecom requirements in specific countries. Also note that some software packages may have features or lack restrictions that may cause the modem to become non-compliant.

New Zealand Telecom Warning Notice

1.The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom’s network services.

This equipment is not capable under all operating conditions of correct operation at the higher speed which it is designated. 33.6 kbps and 56 kbps connections are likely to be restricted to lower bit rates when connected to some PSTN implementations. Telecom will accept no responsibility should difficulties arise in such circumstances.

2.Immediately disconnect this equipment should it become physically damaged, and arrange for its disposal or repair.

3.This modem shall not be used in any manner which could constitute a nuisance to other Telecom customers.

Multi-Tech Systems, Inc. MT5600BA/BL Series User Guide (S000276E)

49

Image 49
Contents Data/Fax Modem User Guide MT5600BA/BL SeriesMT5600BA-V.92 MT5600BA-V.90 MT5600BL-V.90 Record of Revisions MultiModemII User GuideTrademarks PatentsTable of Contents Table of ContentsMultiModemII User Guide None of the Indicators Light About AT Commands Chapter 1 - Description and FeaturesFeatures Product DescriptionSafety Warnings Step 1 - Connect the Modem to Your System Connect theTwo-Wire Leased LineConnect the Modem to Your PC Connect the Modem to the Telephone Line Dialup ConnectionConnect the Modem to the AC Power Outlet Connect the Four-Wire Leased LinePower-On Test Connect the Phone to the Modem OptionalInstalling the Modem Driver for Windows 98/Me/2000 XP Step 2 - Install the Modem DriverInstalling the Modem Driver for Windows NT Removing an Old Modem DriverUsing the LCD Panel Step 3 - Setting Your Country or Region CodeUsing the Global Wizard MT5600BA-V.92 OnlyUsing AT Commands Step 4 - Install PhoneToolsHow to Change the Country/Region Code How to Verify the CodeModem Configuration Chapter 3 - Using the Front PanelLED Indicators Option Selection Liquid Crystal Display LCDMenu Structure Trunks Menu OverviewLimbs BranchesLimbs Twigs Status TrunkLimbs Basic Options TrunkBranches TwigsContinued from previous page Basic Options Trunk, continuedAdvanced Options Trunk Advanced Options Trunk, continued Diagnostic Options Trunk Remote Configuration Options TrunkLimb Caller ID Options Trunk Phone Number Memory Options TrunkStatus Menu OptionsBasic Options ASYNC, NORM? Normal asynchronous transmission using the Advanced Options VIEW S-REGISTER SETTINGS. Use the Æ, È, ÇÅ, and Enter buttons to select the number of the S-register whose value you want displayed. To scroll through a list of digits, press the ÇÅ and È buttons. To go to the next position, press the Æ button. To back up or to exit without saving, press the Æ button several times. To display the value, press the Enter button. Same as the Sr? command Diagnostic Options Remote Configuration OptionsPhone Number Memory Options Caller ID Options Chapter 4 - Leased Line Operation Two-Wire SetupFour-Wire Setup Dial Backup and Leased Line Restoral Setup Dial Backup and Leased-Line Restoral10. Press the Æ button to go to the next digit in the number Basic Procedure Chapter 5 - Remote ConfigurationSetup Changing the Remote Configuration PasswordChanging the Remote Escape Character AT Command Method Setup ProceduresChapter 6 - Callback Security Turning Callback Security On and OffAT Command Method Assigning Callback PasswordsFront Panel Method Front Panel Method Assigning Callback Phone NumbersCalling Procedure Command #DBn Callback Enable/Disable Callback Security CommandsCommand #CBN y= - x Store Callback Number Command #CBP y= x Store Callback PasswordCallback Assignments Form LocationPasswordPhone NumberNone of the Indicators Light Chapter 7 - TroubleshootingThe Modem Does Not Respond to Commands The Modem Cannot Connect When Dialing The Modem Disconnects While Online File Transfer Is Slower Than It Should Be The Modem Cannot Connect When AnsweringData Is Being Lost The Modem Doesn’t Work with Caller ID There Are Garbage Characters on the MonitorFax and Data Software Can’t Run at the Same Time FCC Part 68 Telecom Appendix A - Regulatory ComplianceCanadian Limitations Notice Fax Branding StatementInternational Modem Restrictions EMC, Safety, and R&TTE Directive ComplianceNew Zealand Telecom Warning Notice South African Notice Appendix B - Technical Specifications loop Appendix D - Upgrading the Firmware Upgrade OverviewIntroduction Step 1 - Identify the Modem FirmwareStep 4 - Extract the Upgrade Files Step 3 - Download the Upgrade FileStep 2 - Identify the Current Firmware Version Step 7 - Restore Your Parameters Step 6 - Upgrade the Modem’s FirmwareStep 5 - Clear Your Stored Paramenters Using the Terminal Program Minicom to Verify Operation Appendix E - Installing a Modem Under LinuxStandard Linux Serial Port Definitions InstallationCalling the ISP Using the Modem to Call the InternetAnswering Calls 3. Select Dialup Configuration ToolRS-232 Pin Descriptions Appendix F - Pin DescriptionsAppendix F - Pin Descriptions RS-232 Cable PinoutsDTE Mini-DIN 8-pin connector Leased Line PinoutsDCE DB-25 connector HSKi CTS HSKo RTSIndex