Sony LDI-100B operating instructions Information, Declaration of Conformity

Page 2

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

The AC power cord must be changed only at qualified service shop.

The nameplate is located on the bottom of the power supply box.

Use a commercially available AC plug adapter, if necessary, depending on the design of the wall outlet.

CAUTION

To prevent electric shock, match wide blade of plug to wide slot, fully insert.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Declaration of Conformity

Trade Name:

SONY

Model No.:

LDI-100B/100BE

Responsible Party:

Sony Electronics Inc.

Address:

1 Sony Drive, Park Ridge,

 

NJ.07656 USA

Telephone No.:

201-930-6970

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

2-US

Image 2
Contents Personal LCD Display Information Declaration of ConformityPour les utilisateurs au Canada PrecautionsFor the customers in Canada For the customers in EuropePage Table of Contents Laser disc player, Camcorder About the Personal LCD DisplayPersonal Computer DVD playerFeatures Locating the parts and controls Display unitPower supply box Connecting other IBM compatible PCs Connecting the Personal LCD DisplayConnecting a PC Connecting a Macintosh Powerbook Connector Audio cable RGB signal cable Signal flow Connecting a Macintosh desktop modelsConnecting the Personal LCD Display MacintoshCamcorder, etc Connecting video equipmentTo audio/video output To AUDIO/VIDEO connector Special miniplug Phono plugVideo If your video equipment has an S-video jackAudio L Audio R Connecting the power source Loosen the back strap Adjust the strapWearing the Personal LCD Display Put on the Personal LCD DisplayAdjust the stereo earphones Adjusting the back strapAdjust the angle of the display unit Front padWhen you connect to the S-video connector Adjust the sound volume by turning the VOL control Input the signal from the connected equipmentAdjust the brightness by turning the Bright control Darker brighterInput signal Mega Bass Avls After you finish using Personal LCD DisplayUsing the Personal LCD Display Checking the display indicationsTurn the SEE-THROUGH dial Set the Screen switch to onViewing the surrounding environment PC mode RGB signal Adjusting the sound and pictureSignal compatibility Video mode video signalAdjusting the sound/picture HUE Ntsc Video mode onlyPC mode Adjusting the sound and picture Press MenuAdjust the setting using the jog dial Video modeIndicator Avls Auto Volume Limiter SystemPicture Power Turn the jog dial to set to ON, then press the jog dialAdjusting the RGB signal Adjusting the sound and pictureHUE Ntsc Video mode only Adjusting the video signalResetting the adjustments to the factory preset level LessmoreAttach the battery pack to the power supply box Using the optional battery packCharging the battery pack Connect the AC power adapter to the DC in connector onMark appears on Checking the remaining battery lifeFully Remaining battery life Dead Charged ScreenUse PrecautionsInstallation Unified polarity plugOthers Error messages OUT of Scan RangeTroubleshooting Symptom Cause RemedyTroubleshooting Pin Assignment SpecificationsPin No Signal Y, Z IndexK, L, M, N O