Dell R210 owner manual Installing System Components

Page 104

6Tighten the ten screws that secure the system board to the chassis. See Figure 3-20.

7Transfer the processor and the heat sink to the new system board. See "Removing a Processor" on page 92 and "Installing a Processor" on page 96.

8Replace all the memory modules and memory blanks. See "Installing Memory Modules" on page 81.

9Connect the cables in the order listed below (see Figure 6-1for the locations of the connectors on the system board):

•SATA interface cable, if applicable

•Control panel interface cable

•Optical drive power cable

•Control panel USB interface cable

•System board power cables

10Install the expansion card, if any. See "Installing an Expansion Card" on page 72.

11If applicable, reinstall the iDRAC6 Enterprise card. See "Installing an iDRAC6 Enterprise Card" on page 89.

12If applicable, reinstall the iDRAC6 Express card. See "Installing an iDRAC6 Express Card" on page 86.

13Replace the cooling shroud. See "Installing the Cooling Shroud" on page 79.

14Close the system. See "Closing the System" on page 63.

15Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

106

Installing System Components

Image 104

Contents Dell PowerEdge R210 Systems August Contents Using the System Setup Program Installing System Components Removing the Cooling Shroud Installing the Cooling Shroud Troubleshooting Your System Running the System Diagnostics Getting Help Contacting Dell Glossary Index Contents Accessing System Features During Startup About Your SystemFront-Panel Features and Indicators NMI button Used to troubleshoot softwareBack panels light blue until one Back-Panel Features and Indicators Guidelines for Connecting External Devices NIC Indicator Codes Diagnostic Lights PostInformation on the drives Rebooting System MessagesBios OS NIC=ENABLED Invalid Address, read Memtest lane No boot sector on Quad rank Dimm Sector not Match in rank Count x,x TPM Unexpected Is message Diagnostics Messages Alert MessagesOther Information You May Need About Your System Using the System Setup Program and Uefi Boot Manager Choosing the System Boot ModeUsing the System Setup Program Navigation Keys Entering the System Setup ProgramResponding to Error Messages System Setup Options Main ScreenOptions. See Integrated Devices Screen on Memory Settings Screen Processor Settings ScreenSata Settings Screen Boot Settings Screen Integrated Devices Screen NIC2PCI IRQ Assignments Screen Serial Communication ScreenPower Management Screen System Security Screen Enables or disables the NMI feature NMI Button Disabled defaultExit Screen Entering the Uefi Boot ManagerUsing the Uefi Boot Manager Navigation Keys Uefi Boot Manager Screen Uefi Boot Settings ScreenSystem Utilities Screen System and Setup Password FeaturesUsing the System Password Using the System Setup Program and Uefi Boot Manager Using the System Setup Program and Uefi Boot Manager Using the Setup Password Embedded System Management Entering the BMC Setup Module Baseboard Management Controller ConfigurationIDRAC Configuration Utility Entering the iDRAC Configuration Utility Using the System Setup Program and Uefi Boot Manager Installing System Components Recommended ToolsInside the System Removing the Front Bezel Installing the Front BezelFront Bezel Optional Opening and Closing the System Opening the SystemClosing the System Opening and Closing the System Cover Latch release lockOptical Drive Optional Removing an Optical DriveRelease latch Installing System Components Installing an Optical Drive Hard Drives Removing a Hard DriveDrive bracket Release pin Hard drive Data cable Power cable Installing a Hard Drive Removing a Hard Drive From a Hard-Drive Bracket Installing a Hard Drive Into a Hard-Drive Bracket Expansion Card Expansion Card Installation GuidelinesInstalling an Expansion Card Removing an Expansion Card Expansion-Card Riser Removing an Expansion-Card RiserInstalling an Expansion-Card Riser Internal USB Memory Key Cooling Shroud Removing the Cooling Shroud10. Installing and Removing the Cooling Shroud Touch points System Memory Installing the Cooling ShroudGeneral Memory Module Installation Guidelines Mode-Specific Guidelines Installing Memory Modules Page Removing Memory Modules Cooling Fans Removing a Cooling FanInstalling a Cooling Fan 12. Removing and Installing a FanInstalling an iDRAC6 Express Card IDRAC6 Express Card Optional13. Installing or Removing an iDRAC6 Express Card Removing an iDRAC6 Express Card Installing an iDRAC6 Enterprise Card IDRAC6 Enterprise Card OptionalIDRAC6 Enterprise card connector Removing an iDRAC6 Enterprise Card Installing a VFlash Media Card VFlash Media OptionalProcessor Removing a VFlash Media CardInstalling System Components Installing System Components 16. Installing and Removing a Processor Installing a Processor Your system supports a 250 W power supply module Power SupplyRemoving the Power Supply Sata power cables Replacing the System Battery System BatteryInstalling the Power Supply 18. Replacing the System Battery System battery 100101 Control Panel AssemblyRemoving the Control Panel Assembly 102 19. Control Panel Removal Control panel cableInstalling the Control Panel Assembly System BoardRemoving the System Board 103Installing System Components 105 Installing the System BoardUnpack the new system board Installing System Components Troubleshooting External Connections 109110 Troubleshooting the Video SubsystemTroubleshooting a USB Device 111 Troubleshooting a Serial I/O DeviceTroubleshooting a NIC Troubleshooting a Wet System Troubleshooting a Damaged System 113Troubleshooting the System Battery 115 Troubleshooting Power SupplyTroubleshooting System Cooling Problems Troubleshooting a Fan Troubleshooting System Memory117 Troubleshooting an Internal USB Key Troubleshooting an Optical Drive Troubleshooting a Tape Backup UnitTry using a different CD or DVD 119Troubleshooting a Hard Drive 120Troubleshooting an Expansion Card 121Troubleshooting the Processor 125 Using Online DiagnosticsEmbedded System Diagnostics Features When to Use the Embedded System Diagnostics Running the Embedded System DiagnosticsSystem Diagnostics Testing Options Click the testing option in the Main Menu windowUsing the Custom Test Options Selecting Devices for TestingSelecting Diagnostics Options Viewing Information and ResultsRunning the System Diagnostics System Board Jumpers 129System Board Connectors 130131 IORISER1Disabling a Forgotten Password Contacting Dell 133134 Glossary 135136 137 138 139 Mm Millimeters Ms Milliseconds140 141 142 System memory See RAM143 144 Index 145146 Post 147USB device Back-panel connectors USB key troubleshooting 148149 150

Related manuals

Manual 72 pages 16.2 Kb