Compatible Systems A00-1869, Enterprise-8 manual IPX Protocol, AppleTalk Protocol

Page 30

Chapter 6 - Basic Configuration Guide

24

IPX Protocol

Required for IPX

Generally, there are no required changes from the shipping Ethernet configuration for IPX. The Ethernet interface will autoconfigure to use the two most common IPX frame types, and will automatically adapt to conditions on the Ethernet.

Suggested for IPX

You may want to set your own network numbers, rather than using the autoconfigured values. You may also want to turn off unused frame types.

CV: Use the IPX Routing: Ethernet Dialog Box for Ethernet 0:0, 2:0, 4:0, and 6:0.

TB: Use configure and set keywords in the IPX Ethernet 0:0, IPX Ethernet 2:0, IPX Ethernet 4:0 and IPX Ethernet 6:0 sections.

AppleTalk Protocol

Required for AppleTalk

Generally, there are no required changes from the shipping Ethernet configuration for Apple- Talk. The Ethernet interface will autoconfigure to use AppleTalk Phase 2, and will adapt to conditions on the Ethernet.

Suggested for AppleTalk

You may want to set your own network numbers, rather than using the autoconfigured values. You may also want to use more meaningful zone names.

CV: Use the AppleTalk Routing:Ethernet Dialog Box for Ethernet 0:0, 2:0, 4:0, and 6:0.

TB: Use configure and set keywords in the AppleTalk Phase 2 Ethernet 0:0, AppleTalk Phase 2 Ethernet 2:0, AppleTalk Phase 2 Ethernet 4:0 and AppleTalk Phase 2 Ethernet 6:0 sections.

Configuring the Server for LAN-to-LAN Tunnels

Required for LAN-to-LAN Tunnel Configurations

LAN-to-LAN tunneling requires that you set parameters for a VPN port on each end of a tunnel, so you must repeat this setup on the remote end.

•Partner IP address

•Bind To interface

CV: Add a VPN Port using the File menu and selecting VPN Port/Add VPN Port. Then use the Tunnel Partner: VPN port number Dialog Box for the port(s) you created to set these parameters.

TB: Use configure and set the Partner and BindTo keywords in the Tunnel Partner VPN port number section.

Suggested for LAN-to-LAN Tunnel Configurations

It is recommended that you also set authentication and encryption parameters for each tunnel.

CV: Use the Tunnel Partner: VPN port number Dialog Box for the port you created to set these parameters.

TB: Use configure and set keywords in the Tunnel Partner VPN port number section.

Image 30

Contents IntraPort Enterprise-8 VPN Access Server Installation Guide Page Command Line Management Network InstallationCompatiView Software Installation Introduction to the IntraPort Enterprise-8LED Patterns and Test Switch Settings Basic Configuration GuideShipping Defaults Appendix a Connector and Cable Pin OutsAppendix F Terms and Conditions IiiLocation of Voltage Switch on the Power Supply IntraPort Enterprise-8 Installation Overview Introduction to the IntraPort Enterprise-8IntraPort Enterprise-8 Manual Overview Few Notes Warranty and ServiceGetting Started Please Read the ManualsAdditional Items Needed for Installation What You Will Need to Get StartedSupplied with the IntraPort Enterprise-8 Placement Considerations Safety GuidelinesMounting Instructions Changing the Power Supply Voltage Settings Parts and ToolsInstalling Mounting Ears and Handles Installing Mounting Ears for a Telco RackRack-Mount Brackets Rack-Mount BracketsRight Bracket Installation Fastening the Right Bracket to the RackLeft Bracket Installation Fastening the Left Bracket to the RackSecuring the Shelf Lowering the ShelfMoving the Unit into the Rack Moving the Unit into a Standard Equipment RackPlacing the Unit in an Equipment Rack Placing the Unit in a Standard Equipment RackSecuring the Unit to the Rack Securing the Unit to the RackNetwork Installation Physical Connection RequirementsConnecting the Server to the Ethernet Detail of Riop CardsConnecting a Management Console Powering Up the ServerPower Alarm Information CompatiView for Windows CompatiView Software InstallationInstallation and Operation System RequirementsTransport Protocols and CompatiView Command Line Management Out-of-Band Command Line ManagementSetting Up Telnet Operation IP Settings for Setups in Parallel with a Firewall Basic Configuration GuideEthernet Interface Configuration IP ProtocolIP Settings for Setups Behind a Firewall Configuring the Server for LAN-to-LAN Tunnels IPX ProtocolAppleTalk Protocol Suggested for Client Tunnel Configurations Configuring the Server for IP and IPX Client TunnelsRequired for Client Tunnel Configurations VPN User DatabaseSetting up Radius Authentication Setting the IntraPort Enterprise-8 for a Radius ServerRadius Server User Authentication Settings Setting up SecurID Authentication Setting the IntraPort Enterprise-8 for an ACE/ServerACE/Server Settings Saving a Configuration File to Flash ROM Shipping Defaults Default PasswordEthernet Interfaces IntraPort Enterprise-8 LED Patterns IntraPort Enterprise-8 Switch Settings Appendix a Connector and Cable Pin Outs Pin Outs for DB-25 Male to DB-25 Female Console CableAppendix B Downloading Software From Compatible Systems Appendix C Security Dynamics ACE/Server Information Appendix D Adding or Replacing Riop Cards Removing and Replacing an Riop Card or Cover PlateAppendix E When the Over Temp Light Comes On Replacing or Cleaning the Intraport Enterprise-8 Air FilterAppendix F Terms and Conditions Appendix F Terms and Conditions