Silex technology SX-200 user manual User’s Guide Print Server Components

Page 10

User’s Guide

Print Server Components

The print server includes the following components. Detailed descriptions of these components are provided below:

Power connector – The power supply cable plugs into this connector.

Test button – Pressing this button for less than three seconds will print a test page on the printer. Pressing and holding this button for more than five seconds will reset the print server to factory default settings.

LED status indicators – used to indicate the operational states of the print server. Refer to the LED status light descriptions on the next page.

Ethernet Port – This port is used for connecting the print server to a 10/100Base-TX Ethernet card, hub, router, or other wired access point for network access.

Parallel port – The parallel port is used for connecting the print server to the IEEE 1284-compliant parallel port of your printer (parallel port models only).

USB port – The USB port is used for connecting the print server to the USB 2.0 port of your printer. You must use a standard USB A (print server side) to B (printer side) cable (USB port models only).

NOTE: A USB 2.0 cable must be used to take full advantage of the high-speed USB 2.0 connection.

Document #40181-420 Rev. A

10

Image 10

Contents SX-200 User’s GuideSET NW AUTHtype SET NW CHannelUser’s Guide SET Port U1 Nbuf ENable DIsable SET Power Window nnnn SH POP3 SH Smtp Introduction Package Contents Product OverviewWindows System Requirements User’s Guide About This User’s GuideOther Operating System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State StatusWireless Default Settings wireless print servers only Factory Default SettingsDefault Settings wired and wireless print servers Pushbutton FunctionsHardware Installation Before You BeginUser’s Guide User’s Guide Verifying the Connection to the Printer ExtendView Utility Configuration and ManagementConfiguration Options Web Browser InterfaceHP Web JetAdmin Utility Configuration ConsoleDocument #40181-420 Rev. a User’s Guide Telnet User’s Guide Windows Print Queue Configuration Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Printing Problems TroubleshootingIntroduction Troubleshooting Windows Problems Checking the Network Connection and CablingUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States UsersUser’s Guide Declaration of Conformity FCC Information for Canadian Users IC noticeUser’s Guide Information for European Users Declaration of Conformity CEAppendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Telnet Command Console Access Command console access informationNetwork Commands Serial Port Command Console AccessSH NW ENC SH NW AuthSET NW ENC SET NW KEY#SET NW Keyval SH NW ModeSH NW Speed SET NW Apden SET NW RTSSH NW RTS SH NW ApdenSH NW Certcn SH NW StatsSET NW Certcn SET NW CERTCN2SH NW Certexp SH NW CERTCN2SET NW Certexp SET NW CertkeySH NW Inap SET NW PWSET NW Inap SET NW RealmSH NW Wpagroup SH NW WpaautoSET NW Wpagroup SET NW WpapskSH NW DFS SH NW Iroam NW IroamSET NW DFS SET NW REGDOMainSerial Port Commands Port CommandsSET NW Wired SH NW REGDOMainSet serial port parity to NONE, EVEN, ODD, MARK, or Space SET Port S1 SPeedSet serial port flow control to NONE, XON/XOFF, CTS, or DSR Sets the data bits on the serial portSET Port P1 BIDir User’s Guide Parallel Port CommandsEnable or disable bidirectional mode Shows Port parameters Sample outputEnable or disable PJL status initialization SET Port P1 Nbuf ENable DIsableCL Port port JOB SET SERVEr DEscription Server Information CommandsUSB Port Commands SET SERVEr NAmeSET Snmp SETCOMM2 SET Snmp SETCOMM1SH Serial SH Snmp SH SERVErSH SERVEr CO SH VErsionService Commands SET Servi service name NAme SET Servi service name FRSSET Servi service name IP SET Servi service name POrtString Commands User’s Guide SH STRing stringnum TCP/IP CommandsSET IP ACcess SH FILtersSET IP Chksum SET IP Http SET IP FTPSET IP LPD SET IP TCP SET IP TftpPower Configuration Commands SH IPUser’s Guide Firmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAdExit Other CommandsSET Default SH FreeSH Poweron SET PoweronSave Netware Commands UnprotectSET Netw SErver SET Netw QServerSET Netw REscan CL Netw SErverEmail Printing Commands SET Smtp ENable SET POP3 PAsswordSET POP3 TImeout SET Smtp ADdressSH Smtp DLC / Netbeui CommandsSH POP3 SH DLCAppletalk Commands Wireless Security Configuration ExtendViewKey Selection SH NW SET NW KEY# SET NW RTS SH NW Apden SH NW CERTCN2 SET NW Inap SH NW Wpagroup