Silex technology Understanding the Silex Default Password and Device Functions

Page 12

User’s Guide

Pushbutton Functions

The front edge of the print server provides a momentary pushbutton that can be used to print a test/configuration page or reset the device to factory default settings.

Action

Function

Press pushbutton for > 1/8 second but < 5

Prints a test/configuration page on each connected port

seconds

 

 

 

Press pushbutton for > 5 seconds

Resets the device configuration to factory defaults. The

 

unit will reinitialize itself after updating the

 

configuration memory.

 

 

Factory Default Settings

The SX-200 Series Print Server is shipped with a default configuration. The settings can be changed to suit specific installation requirements via the ExtendView Utility, or other SNMP-based utilities, the embedded Web server, or via a Telnet connection to the Print Server’s internal console. The factory default settings can be easily restored at any time by performing a cold reset (press and hold the pushbutton on the device for more than five seconds).

Default Settings (wired and wireless print servers)

Parameter

Setting

IP Address

190.0.0.192

 

 

TCP/IP Method

AUTO (BootP and DHCP are enabled)

 

 

Password

access

 

 

Wireless Default Settings (wireless print servers only)

Parameter

Setting

Wireless Mode

Ad-Hoc (peer-to-peer)

 

 

RF Channel

11

 

 

ESSID

printer (lower case)

 

 

Document #40181-420 Rev. A

12

Image 12
Contents SX-200 User’s GuideSET NW AUTHtype SET NW CHannelUser’s Guide SET Port U1 Nbuf ENable DIsable SET Power Window nnnn SH POP3 SH Smtp Introduction Package Contents Product OverviewUser’s Guide About This User’s Guide Windows System RequirementsOther Operating System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State StatusFactory Default Settings Default Settings wired and wireless print serversWireless Default Settings wireless print servers only Pushbutton FunctionsHardware Installation Before You BeginUser’s Guide User’s Guide Verifying the Connection to the Printer Configuration and Management Configuration OptionsExtendView Utility Web Browser InterfaceHP Web JetAdmin Utility Configuration ConsoleDocument #40181-420 Rev. a User’s Guide Telnet User’s Guide Windows Print Queue Configuration Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Troubleshooting Printing ProblemsIntroduction Troubleshooting Windows Problems Checking the Network Connection and CablingUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States UsersUser’s Guide Declaration of Conformity FCC Information for Canadian Users IC noticeUser’s Guide Information for European Users Declaration of Conformity CEAppendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Command console access information Network CommandsTelnet Command Console Access Serial Port Command Console AccessSH NW Auth SET NW ENCSH NW ENC SET NW KEY#SH NW Mode SET NW KeyvalSH NW Speed SET NW RTS SH NW RTSSET NW Apden SH NW ApdenSH NW Stats SET NW CertcnSH NW Certcn SET NW CERTCN2SH NW CERTCN2 SET NW CertexpSH NW Certexp SET NW CertkeySET NW PW SET NW InapSH NW Inap SET NW RealmSH NW Wpaauto SET NW WpagroupSH NW Wpagroup SET NW WpapskSH NW Iroam NW Iroam SET NW DFSSH NW DFS SET NW REGDOMainPort Commands SET NW WiredSerial Port Commands SH NW REGDOMainSET Port S1 SPeed Set serial port flow control to NONE, XON/XOFF, CTS, or DSRSet serial port parity to NONE, EVEN, ODD, MARK, or Space Sets the data bits on the serial portUser’s Guide Parallel Port Commands Enable or disable bidirectional modeSET Port P1 BIDir Shows Port parameters Sample outputSET Port P1 Nbuf ENable DIsable Enable or disable PJL status initializationCL Port port JOB Server Information Commands USB Port CommandsSET SERVEr DEscription SET SERVEr NAmeSET Snmp SETCOMM1 SET Snmp SETCOMM2SH Serial SH SERVEr SH SERVEr COSH Snmp SH VErsionService Commands SET Servi service name FRS SET Servi service name IPSET Servi service name NAme SET Servi service name POrtString Commands TCP/IP Commands SET IP ACcessUser’s Guide SH STRing stringnum SH FILtersSET IP Chksum SET IP FTP SET IP HttpSET IP LPD SET IP TCP SET IP TftpPower Configuration Commands SH IPUser’s Guide Firmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAdOther Commands SET DefaultExit SH FreeSET Poweron SH PoweronSave Netware Commands UnprotectSET Netw QServer SET Netw REscanSET Netw SErver CL Netw SErverEmail Printing Commands SET POP3 PAssword SET POP3 TImeoutSET Smtp ENable SET Smtp ADdressDLC / Netbeui Commands SH POP3SH Smtp SH DLCAppletalk Commands Wireless Security Configuration ExtendViewKey Selection SH NW SET NW KEY# SET NW RTS SH NW Apden SH NW CERTCN2 SET NW Inap SH NW Wpagroup