Silex technology SX-200 user manual SH NW Wpaauto, SET NW Wpagroup, SH NW Wpagroup, SET NW Wpapsk

Page 44

User’s Guide

Enable or disable WPA auto mode. If enabled, the print server will connect to a non-WPA access point if a WPA


enabled access point is not available.		Only valid when WPA is enabled (authentication type = TKIP).
SET NW WPAAUTO	[ENable DIsable]
(default	= disabled)

SH NW WPAAUTO

Shows the state of the WPA auto connect flag

sample output:

WPA-AUTO Enabled

SET NW WPAGROUP

Enable or disable WPA group key mode. If enabled, this allows group keys to be used for data link encryption.

SET NW WPAGROUP [ENABLE DISABLE] (default = disabled)

SH NW WPAGROUP

Shows the state of the allow WPA group keys flag

sample output:

WPA-GROUP Disabled

SET NW WPAPSK

Sets the WPA PSK pass phrase or hex key. This value is only used if the authentication mode is WPA-PSK. The argument to this command is either a pass phrase of 8-63 characters, or exactly 64 hex characters representing the 256 bit PSK value.

SET NW WPAPSK <key> (default = “silex Group”)

SET NW WPATRACE

Sets the WPA trace level. note: this command is for diagnostic purposes only, and should not normally be used as the trace can affect performance. A value of 0 disables the trace.

SET NW WPATRACE nn (default = 0)

SET NW IROAM

Document #40182-420 Rev. A

44

Image 44

Contents SX-200 User’s GuideSET NW AUTHtype SET NW CHannelUser’s Guide SET Port U1 Nbuf ENable DIsable SET Power Window nnnn SH POP3 SH Smtp Introduction Package Contents Product OverviewOther Operating System Requirements User’s Guide About This User’s GuideWindows System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State StatusFactory Default Settings Default Settings wired and wireless print serversWireless Default Settings wireless print servers only Pushbutton FunctionsHardware Installation Before You BeginUser’s Guide User’s Guide Verifying the Connection to the Printer Configuration and Management Configuration OptionsExtendView Utility Web Browser InterfaceHP Web JetAdmin Utility Configuration ConsoleDocument #40181-420 Rev. a User’s Guide Telnet User’s Guide Windows Print Queue Configuration Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Introduction TroubleshootingPrinting Problems Troubleshooting Windows Problems Checking the Network Connection and CablingUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States UsersUser’s Guide Declaration of Conformity FCC Information for Canadian Users IC noticeUser’s Guide Information for European Users Declaration of Conformity CEAppendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Command console access information Network CommandsTelnet Command Console Access Serial Port Command Console AccessSH NW Auth SET NW ENCSH NW ENC SET NW KEY#SH NW Speed SH NW ModeSET NW Keyval SET NW RTS SH NW RTSSET NW Apden SH NW ApdenSH NW Stats SET NW CertcnSH NW Certcn SET NW CERTCN2SH NW CERTCN2 SET NW CertexpSH NW Certexp SET NW CertkeySET NW PW SET NW InapSH NW Inap SET NW RealmSH NW Wpaauto SET NW WpagroupSH NW Wpagroup SET NW WpapskSH NW Iroam NW Iroam SET NW DFSSH NW DFS SET NW REGDOMainPort Commands SET NW WiredSerial Port Commands SH NW REGDOMainSET Port S1 SPeed Set serial port flow control to NONE, XON/XOFF, CTS, or DSRSet serial port parity to NONE, EVEN, ODD, MARK, or Space Sets the data bits on the serial portUser’s Guide Parallel Port Commands Enable or disable bidirectional modeSET Port P1 BIDir Shows Port parameters Sample outputCL Port port JOB SET Port P1 Nbuf ENable DIsableEnable or disable PJL status initialization Server Information Commands USB Port CommandsSET SERVEr DEscription SET SERVEr NAmeSH Serial SET Snmp SETCOMM1SET Snmp SETCOMM2 SH SERVEr SH SERVEr COSH Snmp SH VErsionService Commands SET Servi service name FRS SET Servi service name IPSET Servi service name NAme SET Servi service name POrtString Commands TCP/IP Commands SET IP ACcessUser’s Guide SH STRing stringnum SH FILtersSET IP Chksum SET IP LPD SET IP FTPSET IP Http SET IP TCP SET IP TftpPower Configuration Commands SH IPUser’s Guide Firmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAdOther Commands SET DefaultExit SH FreeSave SET PoweronSH Poweron Netware Commands UnprotectSET Netw QServer SET Netw REscanSET Netw SErver CL Netw SErverEmail Printing Commands SET POP3 PAssword SET POP3 TImeoutSET Smtp ENable SET Smtp ADdressDLC / Netbeui Commands SH POP3SH Smtp SH DLCAppletalk Commands Wireless Security Configuration ExtendViewKey Selection SH NW SET NW KEY# SET NW RTS SH NW Apden SH NW CERTCN2 SET NW Inap SH NW Wpagroup