Silex technology SX-200 Configuration and Management, Configuration Options, ExtendView Utility

Page 16

User’s Guide

Section 3 – Configuration and Management

Configuration Options

SX-200 Series Print Servers (wired and wireless models) can be configured using a variety of options, some of which do not require any software installation on the host PC. The print server can be configured and managed via an Ethernet or wireless connection using the ExtendView Utility (recommended), the embedded web (HTTP) server pages, or the print server’s internal configuration console, which can be accessed via a Telnet connection. If you choose to use the silex ExtendView Utility (provided on the Print Server Installation CD), the software must be installed prior to use. Additional options for print server configuration and management are available as third-party utilities that can be downloaded from their respective web sites. If you are using a wireless print server, you can still configure it via an Ethernet connection or optionally configure it via a wireless connection.

ExtendView Utility

used for advanced print server configuration, and allows you to configure for TCP/IP, Netware, AppleTalk, and the wireless settings (for wireless print server models only).

uses a 32-bit graphical user interface.

works with Windows PCs running the TCP/IP protocol.

included on the Print Server installation CD.

can be downloaded from the silex web sites: USA: http://www.silexamerica.com

after installation, this utility can be run from the START menu.

INSTALLING THE EXTENDVIEW UTILITY (WINDOWS OPERATING SYSTEMS):

1.Ensure your PC is connected and has access to your network.

2.Connect an available Ethernet cable from your network hub to the print server. Ensure the print server is powered on.

3.Insert the CD supplied with your print server into the CD-ROM drive of your computer. The CD should automatically start and display a menu screen. Click on Install Software.

4.Select ExtendView, and then click on Install.

Web Browser Interface

allows you to configure the print server with a standard web browser (e.g., Internet Explorer or Mozilla).

no additional software is needed on the system.

can be used on any system that supports web browser capabilities.

type the IP address into your web browser address bar to connect.

the default password is ACCESS (all uppercase characters).

Document #40181-420 Rev. A

16

Image 16

Contents SX-200 User’s GuideSET NW AUTHtype SET NW CHannelUser’s Guide SET Port U1 Nbuf ENable DIsable SET Power Window nnnn SH POP3 SH Smtp Introduction Package Contents Product OverviewWindows System Requirements User’s Guide About This User’s GuideOther Operating System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State StatusFactory Default Settings Default Settings wired and wireless print serversWireless Default Settings wireless print servers only Pushbutton FunctionsHardware Installation Before You BeginUser’s Guide User’s Guide Verifying the Connection to the Printer Configuration and Management Configuration OptionsExtendView Utility Web Browser InterfaceHP Web JetAdmin Utility Configuration ConsoleDocument #40181-420 Rev. a User’s Guide Telnet User’s Guide Windows Print Queue Configuration Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Printing Problems TroubleshootingIntroduction Troubleshooting Windows Problems Checking the Network Connection and CablingUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States UsersUser’s Guide Declaration of Conformity FCC Information for Canadian Users IC noticeUser’s Guide Information for European Users Declaration of Conformity CEAppendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Command console access information Network CommandsTelnet Command Console Access Serial Port Command Console AccessSH NW Auth SET NW ENCSH NW ENC SET NW KEY#SET NW Keyval SH NW ModeSH NW Speed SET NW RTS SH NW RTSSET NW Apden SH NW ApdenSH NW Stats SET NW CertcnSH NW Certcn SET NW CERTCN2SH NW CERTCN2 SET NW CertexpSH NW Certexp SET NW CertkeySET NW PW SET NW InapSH NW Inap SET NW RealmSH NW Wpaauto SET NW WpagroupSH NW Wpagroup SET NW WpapskSH NW Iroam NW Iroam SET NW DFSSH NW DFS SET NW REGDOMainPort Commands SET NW WiredSerial Port Commands SH NW REGDOMainSET Port S1 SPeed Set serial port flow control to NONE, XON/XOFF, CTS, or DSRSet serial port parity to NONE, EVEN, ODD, MARK, or Space Sets the data bits on the serial portUser’s Guide Parallel Port Commands Enable or disable bidirectional modeSET Port P1 BIDir Shows Port parameters Sample outputEnable or disable PJL status initialization SET Port P1 Nbuf ENable DIsableCL Port port JOB Server Information Commands USB Port CommandsSET SERVEr DEscription SET SERVEr NAmeSET Snmp SETCOMM2 SET Snmp SETCOMM1SH Serial SH SERVEr SH SERVEr COSH Snmp SH VErsionService Commands SET Servi service name FRS SET Servi service name IPSET Servi service name NAme SET Servi service name POrtString Commands TCP/IP Commands SET IP ACcessUser’s Guide SH STRing stringnum SH FILtersSET IP Chksum SET IP Http SET IP FTPSET IP LPD SET IP TCP SET IP TftpPower Configuration Commands SH IPUser’s Guide Firmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAdOther Commands SET DefaultExit SH FreeSH Poweron SET PoweronSave Netware Commands UnprotectSET Netw QServer SET Netw REscanSET Netw SErver CL Netw SErverEmail Printing Commands SET POP3 PAssword SET POP3 TImeoutSET Smtp ENable SET Smtp ADdressDLC / Netbeui Commands SH POP3SH Smtp SH DLCAppletalk Commands Wireless Security Configuration ExtendViewKey Selection SH NW SET NW KEY# SET NW RTS SH NW Apden SH NW CERTCN2 SET NW Inap SH NW Wpagroup