NCR 7882 manual Programming Defaults, Upc/Ean

Page 14

NCR RealScan 7882 Installation and Owner Guide

Programming Defaults

Scanning the Default programming tag sets most program parameters to factory defined values as shown in the following chart. However, some parameters do not have default values so they are not changed, they stay as they are programmed.

01 Communications Protocol
Protocol	No default value – remains as programmed

11 Good Read Tone
Tone On/Off	On
Tone Frequency	Choice 6 of 8 Levels
Tone Length	Choice 3 of 16 Levels
Tone Volume	Choice 4 of 8 Levels
Not-On-File Volume	Choice 2 of 8 Levels

12 Timers
Lockout Time	750 Milliseconds
Restart Lockout Timer	Off
Active Time	15 Minutes

13 Bar Codes – 1
UPC/EAN	Enable
Version D	Disable
Extend UPC-A To EAN-13	Disable
Extend UPC-E To UPC-A	Disable
Periodical Codes	Disable
Periodical Code Extension	2-Digit & 5-Digit
Send Data	Data As Decoded

14 Bar Codes – 2
Code 39	Disable
Minimum Characters Allowed	8
Full ASCII	Disable
Check Digit Present	Disable
Transmit Check Digit	Disable
Allow 1- or 2-Character Tags	Disable

15 Bar Codes – 3
Interleaved 2 of 5	Disable
Bar Code Length	Range Check
Value 1	08
Value 2	16
Check Digit Present	Disable
Transmit Check Digit	Disable

17 Bar Codes – 4
Code 128	Disable
Minimum Data Characters	3
UCC 128	Disable

14 of 62

09/02

497-0419630 Release F

Image 14

Contents RealScan Installation and Owner Guide Contents Revision RecordObtaining Additional Information Obtaining Technical AssistanceRealScan 7882 Mountings RealScanInstallation Instructions StepInstalling Power Supply Interface Cables Connecting the Cables to an NCR RealScanUSB Interface Connection IBM HID Auxiliary RS-232 Port Auxiliary RS-232 PortProgramming the Communication Parameters Setting Program Parameters and Verifying Host ConnectionTurning on the RealScan RS-232 NCR 2170, 7452 Ocia Short Format NCR 2113, 2126 RS-232 Ruby Verifone Ruby 4M Programming Defaults UPC/EANPrefix Byte Disable Ascii Code Programming for USB Connection RS-232 CommunicationsMaking Other Program Changes Scan Sample Tags UPC-ADetermining Label Quality 1234 5 678Setting RealScan Scan Zone Scan Zone Adjusting ScrewHorizontal Pass-by Scanning Vertical Pass-by ScanningVertical Presentation Scanning from Top Vertical Presentation Scanning from BottomPlastic Top Plate Mounting RealScanRubber Feet Connect Power Cable and Interface Cable Vertical Mounting Bracket Cable Clamps Checkstand CutoutCheckpoint Cable Operating the Scanner Cleaning the Scanner Correcting Scanner Problems Green Status Indicator Tones Problem Suspect ComponentNCR RealScan 7882 Installation and Owner Guide Most Common Interface Cables Interface ConnectorInterface Information Protocol Communications ProtocolProgramming Worksheet NCR RealScan Specifications Checkstand Hole RealScan 7882 Horizontal MountCheckstand Hole RealScan 7882 Flat Mount Electrical Wiring Ventilation RequirementsProgramming Worksheets Tone On/OffExtend UPC-E To UPC-A Version DExtend UPC-A To EAN-13 Periodical CodesCheck Digit Present CodeMinimum Characters Allowed Full Ascii Transmit Check DigitCommon Byte Minimum Data Characters Allowed UCCIdentifier Type Bar Code TypeStop Bits Character Length Baud RateParity HandshakeTerminator Byte Message DelayNormal or Eavesdrop Mode IBM Tone Control Good Read Tone ControlAscii Code Chart Regulatory Information Identification Labels CE Mark ApplicabilityDeclaration of Conformity Laser Safety Laser Safety LabelLaser Power Laser Module LabelVolume Adjustment Reset Programming TagsDefault Programming Mode End Save and Reset Abort Diagnostic Mode RS-232 Temporary Service Mode Mode Reset Tallies Hex Hex Hex Hex Hex Hex a Hex B Hex C Hex D Hex E Hex F Copyright 2001, 2002 by NCR Corporation