|
|
|
| Driver Manual |
| |
Read/ | COMMAND NAME | OPTO22_FORMAT | MASTER LENGTH | NOTES | ||
Write/ |
| OPTION | CONSIDERED (See |
|
| |
Both |
|
| Notes) |
|
| |
|
|
| Specified) module positions get set | |||
|
|
|
|
| ||
|
|
|
|
| ||
w | SET LATCH OFF TO ON |
| 3 | Only module positions specified get | ||
|
|
|
|
| affected by command. | |
w | SET LATCH ON TO OFF |
| 3 | Only module positions specified get | ||
|
|
|
|
| affected by command. | |
r | READ LATCHES | 1 | 2 | If format=Bit then length is considered | ||
|
|
|
|
| during storage as bits are unpacked | |
|
|
|
|
| into data array. If format is non equal | |
|
|
|
|
| to bit then result is written as a single | |
|
|
|
|
| value into one array element. | |
b | READ AND CLEAR LATCHES | 1 | 3,2 | |||
|
|
|
|
| positions get affected (cleared) by | |
|
|
|
|
| command. But all positions get read. | |
|
|
|
|
| Read data get stored in data array. | |
|
|
|
|
| During storage opto22_format is | |
|
|
|
|
| considered. If format=bit then data is | |
|
|
|
|
| unpacked and stored otherwise the | |
|
|
|
|
| result for all 16 positions is stored as | |
|
|
|
|
| one data element. | |
w | CLEAR LATCHES |
| 3 | Only module positions specified get | ||
|
|
|
|
| affected by command. | |
w | START/STOP COUNTERS |
| 3 | All positions are affected by | ||
|
|
|
|
| command. | |
|
|
|
|
| module positions start counting, zero | |
|
|
|
|
| (unspecified) module positions stop | |
|
|
|
|
| counting | |
w | START COUNTERS |
| 3 | Only module positions specified get | ||
|
|
|
|
| affected by command. | |
w | STOP COUNTERS |
| 3 | Only module positions specified get | ||
|
|
|
|
| affected by command. | |
r | READ COUNTERS |
| 1 | Data that is read is put into the | ||
|
|
|
|
| corresponding array elements of the | |
|
|
|
|
| data array based on which module | |
|
|
|
|
| positions are read. | |
b | READ AND CLEAR COUNTERS |
| 1 | Data that is read is put into the | ||
|
|
|
|
| corresponding array elements of the | |
|
|
|
|
| data array based on which module | |
|
|
|
|
| positions are read. | |
w | CLEAR COUNTERS |
| 3 | Only module positions specified get | ||
|
|
|
|
| affected by command. | |
w | SET TIME DELAY |
| 3 | The Modifier is specified in the CSV | ||
|
|
|
|
| file with the opto22_modifier1 | |
|
|
|
|
| parameter. The data (timeout) is | |
|
|
|
|
| retrieved from the first element of the | |
w | INITIATE SQUARE WAVE |
| 3 | data array. | ||
|
|
| ||||
w | HIGH RESOLUTION SQUARE WAVE |
| 3 |
|
| |
w | RETRIGGER TIME DELAY |
| 3 | Only module positions specified get | ||
|
|
|
|
| affected by command. | |
w | GENERATE N PULSES |
| 3 | Only specified module positions get | ||
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408)
Visit our website: www.fieldserver.com
Page 21