FieldServer FS-8700-17 instruction manual Only one module position may be

Page 25

 

FS-8700-17 Optomux

 

 

Driver Manual

 

Read/

COMMAND NAME

OPTO22_FORMAT

MASTER LENGTH

NOTES

Write/

 

OPTION

CONSIDERED (See

 

 

Both

 

 

Notes)

 

 

 

 

 

 

 

r

READ AND AVERAGE INPUT

 

4

Only one module position may be

 

 

 

 

 

specified. This position is averaged

 

 

 

 

 

and the result is put in the first

 

 

 

 

 

element of the data array The number

 

 

 

 

 

of samples is specified in modifier1 in

 

 

 

 

 

the csv file.

w

START INPUT AVERAGING

 

3

Only specified module positions get

 

 

 

 

 

affected by command. First element

 

 

 

 

 

in data array is sent as the number of

 

 

 

 

 

sample to average over.

r

READ AVERAGE COMPLETE BITS

1

2

If format=Bit then length is considered

 

 

 

 

 

during storage as bits are unpacked

 

 

 

 

 

into data array. If format is non equal

 

 

 

 

 

to bit then result is written as a single

 

 

 

 

 

value into one array element.

 

 

 

 

 

Retrieved data is stored in standard

 

 

 

 

 

data array.

r

READ INPUT AVERAGE DATA

 

3

Only specified module positions get

 

 

 

 

 

read. Data read gets put in

 

 

 

 

 

corresponding positions of data array.

r

READ TEMPERATURE INPUTS

 

3

Only specified module positions get

 

 

 

 

 

read. Data read gets put in

 

 

 

 

 

corresponding positions of data array.

r

READ AVERAGE TEMPERATURE INPUTS

 

3

Only specified module positions get

 

 

 

 

 

read. Data read gets put in

 

 

 

 

 

corresponding positions of data array.

w

SET INPUT RANGE

 

3

Only specified module positions have

 

 

 

 

 

their range set to the 2 values found

 

 

 

 

 

in the data array. 1st is high limit,

 

 

 

 

 

second is lo limit.

r

READ OUT-OF-RANGE LATCHES

 

4

High limit latches are placed in first

 

 

 

 

 

element of data array. Low limit

 

 

 

 

 

latches are placed in 2nd element of

 

 

 

 

 

data array.

b

READ AND CLEAR RANGE LATCHES

 

3

Only specified module positions get

 

 

 

 

 

read and cleared. Data read gets put

 

 

 

 

 

in corresponding positions of data

w

CLEAR OUT-OF-RANGE LATCHES

 

4

array.

 

 

 

r

READ LOWEST VALUES

 

3

Only specified module positions get

 

 

 

 

 

read. Data read gets put in

 

 

 

 

 

corresponding positions of data array.

w

CLEAR LOWEST VALUES

 

3

Only module positions specified get

 

 

 

 

 

affected by command.

b

READ AND CLEAR LOWEST VALUES

 

3

Only specified module positions get

 

 

 

 

 

read and cleared. Data read gets put

 

 

 

 

 

in corresponding positions of data

 

 

 

 

 

array.

r

READ PEAK VALUES

 

3

Only specified module positions get

 

 

 

 

 

read. Data read gets put in

 

 

 

 

 

corresponding positions of data array.

w

CLEAR PEAK VALUES

 

3

Only module positions specified get

FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042

Visit our website: www.fieldserver.com E-mail: support@fieldserver.com

Page 23

Image 25
Contents FS-8700-17 Optomux Table of Contents Optomux Driver Description Optomux System Driver Scope of SupplyFS-X40 Hardware ConnectionsData Arrays Configuring the FieldServer as a Optomux Driver ClientClient Side Nodes Client Side ConnectionsFieldServer Related Map Descriptor Parameters Client Side Map DescriptorsDriver Related Map Descriptor Parameters Bit, Packed Timing Parameters SET Time Delay Generate N Pulses Read and Average InputsDEVICE77STAT , Discinputs Map Descriptor Example 1 Read on/off StatusRead Status FS-8700-17 Optomux Driver Manual Read STATUS, Responsearr Map Descriptor Example 3 Command Response/Completion StatusDEVICE77STAT , Cntrposns Map Descriptor Example 4 Triggered ActionDEVICE77STAT , Anadata PULSE77 Timedata This example, module positions 1 and 5 are pulsedWrbc , DEV77 , 16 , 10.0s CLRLOW77 LowarrayConfiguring the FieldServer as a Optomux Server Driver Notes Command Response StatusDataArrayName, DABitName, DAByteName Module PositionsOptomux Commands FS-8700-17 Optomux Driver Manual Read Specified module positions get set Affected. The data period of pulses Only one module position may be Calculated and read. Data read gets Driver Stats Array Element ContentsRevision History