Maxtor 94610H6, 93073H4, 96147H8, 91536H2, 92305H3 specifications Glossary, Block

Page 58

GLOSSARY

GLOSSARY

Glossary

A

ACCESS

To obtain data from, or place data into, RAM, a register, or data storage device.

BPI

Acronym for bits per inch. See bit density.

BLOCK

A group of bytes handled, stored, and accessed as a logical data unit, such as an individual file record.

ACCESSTIME

The interval between the issuing of an access command and the instant that the target data may be read or written. Access time includes seek time, latency and controller overhead time.

ADDRESS

A number, generally binary, distinguishing a specific member of an ordered set of locations. In disk engineering, the address may consist of drives (unit address), radial positions (cylinder address), or circumferential position (sector address).

ALLOCATION

A process of assigning designated areas of the disk to particular files.

ALTERNATETRACK

A spare track used in the event that a normal track becomes damaged or is unusable.

ANALOG

A signal or system that does not use digital states to convey information. A signal may have any number of significant states (values), contrasted to digital signals which can only have two states.

BUFFER

A temporary data storage area that compensates for a difference in data transfer rates and/or data processing rates between sender and receiver.

BUS

A collection of functionally parallel conductors that forms an interconnection between functional blocks in a digital device. A length of parallel conductors that forms a major interconnection route between the computer system CPU (central processing unit) and its peripheral subsystems. Depending on its design, a bus may carry data, addresses, power, and more.

BYTE

An ordered collection of bits treated as a unit. Most often, a byte is understood to consist of eight bits. One byte is necessary to define an alphanumeric character.

C

CACHE

Random access memory (RAM) used as a buffer between the CPU and the disk drive.

ANSI

American National Standards Institute.

APPLICATIONPROGRAM

A sequence of programmed instructions that tell the computer how to perform some end-user task, such as accounting or word processing.

AREALDENSITY

Bit density (bits per inch) multiplied by track density (tracks per inch) or bits per square inch.

ASYMMETRY

A distortion of the readback signal which is shown in different intervals between the positive and negative voltage peaks.

AUXILIARYMEMORY

Memory other than main memory; generally a mass-storage subsystem containing disk drives and backup tape drives, controller(s) and buffer memory (also called peripheral memory).

AVERAGEACCESSTIME

The average time to make all possible length accesses (seeks).

AVERAGE SEEK TIME

The average time to make all possible length seeks. A typical measure of performance.

B

BADBLOCK

A block that cannot store data because of a media flaw.

BIT

An abbreviation for binary digit, of which there are two (0 and 1). A bit is the basic data unit of most digital computers. A bit is usually part of a data byte or word, but bits may be used singly to control or read logic “on-off” functions. The fundamental unit information, often used loosely to refer to a circuit or magnetization state at a particular instant in time.

BIOS

Acronym for Basic Input/Output System. The firmware area of a CPU that controls operations through the system bus and to the attached cards and peripheral devices.

CAPACITY

The amount of data, usually expressed in bytes, which can be stored in a given device or portion of same.

CENTRALPROCESSINGUNIT(CPU)

The heart of the computer system that executes programmed instructions. It includes the arithmetic logic unit (ALU) for performing all math and logic operations, a control section for interpreting and executing instructions, internal memory for temporary storage of program variables and other functions.

CHANNEL

A collection of electronic circuits used in the process of writing and reading information to and from magnetic media.

CHARACTER

An ordered collection of bits representing one of a set of predefined symbols. Often the term is used interchangeably with byte, but this is inexact.

CLOSEDLOOP

A control technique that enables the positioning system to correct off-track errors in real time. The actual head position is monitored and compared to the ideal track position to determine any position error that might be occurring. This information is then used to produce a correction signal (feedback) that goes to the positioner to correct the error. (See also track following servo).

CLOSEDLOOPSERVO

A servo control technique that uses position feedback to correct off-track errors. See Track Following Servo.

CLUSTER

The smallest allocatable unit of disk storage allowed by MS-DOS; each FAT entry represents one cluster.

CONTROLLER

An electronic device for connecting one or more mass storage peripherals (rigid disk drives, tape drives, and optical disk drives) to the input/output circuits of a host computer. Controllers vary in complexity, with more sophisticated units able to buffer and schedule commands, correct data errors, and bypass media defects without host intervention.

GL – 1

Image 58
Contents DiamondMax Before You Begin U T I O NContents Product Specifications AT Interface Description Service and Support Figures Manual Organization IntroductionMaxtor Corporation AbbreviationsConventions DiamondMax 60 Key Features Product DescriptionModel CYL Product FeaturesFunctional / Interface MAX LBA CapacityCache Management Major HDA Components Jumper Location / Configuration Subsystem ConfigurationCylinder Limitation Jumper Description Performance Specifications Product SpecificationsDrive Configuration Models and CapacitiesPhysical Dimensions maximum Parameter A N D a R D MetricEPA Energy Star Compliance Power RequirementsPower Mode Definitions Environmental LimitsShock and Vibration Reliability SpecificationsParameter E R a T I N G Safety Regulatory Compliance EMC/EMIHard Drive Handling Precautions Handling and InstallationElectro-Static Discharge ESD Unpacking and Inspection Multi-pack Shipping ContainerPhysical Installation RepackingBefore You Begin Hook upSet up Start upAT Interface Description Interface ConnectorPIN Signal Pin Description SummaryPIN Name Signal Name Signal Description Pin Description TableTiming Parameters Mode PIO TimingDMA Timing Ultra DMA Timing Timing Parameters all times in nanosecondsSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Task File Registers Host Software InterfacePort Read Write N T E N T S LBA Bits Command Register Summary R a M E T E R S U S E DControl Diagnostic Registers Reset and Interrupt Handling Interface Commands Read Commands Read DMA Write Commands Write Multiple Value Description Mode Set/Check CommandsEV E L Value M M a N D Power Mode Commands Timer Value TIME-OUT PeriodSleep Mode Initialization Commands Content Description15 -3 = reserved R D Content Description Initialize Drive Parameters Seek, Format and Diagnostic Commands Error Code DescriptionA.R.T. Command Set Key RegisterNo Quibble Service Service and SupportService Policy SupportFrom Dial Glossary BlockCorrectableerror Fetch Landingzoneorlzone Physicalsector Softerror