Maxtor 94610H6, 93073H4 Shock and Vibration, Reliability Specifications, Parameter E R a T I N G

Page 18

PRODUCT SPECIFICATIONS

Shock and Vibration

PARAMETER	O P E R A T I N G	N O N - O P E R A T I N G
Mechanical Shock	30 Gs, 2 . 0 ms, no errors	250	Gs, 2 . 0 ms, no damage
Rotational Shock		18,000 Rad/sec,0.5 - 1.0 ms, no damage
Random Vibration	10 - 45 Hz at 0.004 G2 /Hz	P S D :
	48 - 62 Hz at 0.008 G 2/Hz	10 Hz at .05 G 2 /Hz
	65 - 300 Hz at 0.004 G 2/Hz	20 Hz at .055 G 2/Hz,
	301 - 500 Hz at 0.0006 G 2/Hz	300	Hz at .05 G 2/Hz
	no errors	301	Hz at .0014 G 2/Hz
		500 - 760 Hz at . 001 G 2 /Hz
		877	Hz at .003 G 2/Hz
		1000-1570 Hz at .001 G 2 /Hz
		2000 Hz at .0001 G 2/Hz
Swept Sine Vibration
10 - 300 Hz	1 G (0 - peak) amplitude, .25 octave per minute

Reliability Specifications

Annual Return Rate
< 1.0%	Annual Return Rate (ARR) indicates the average against products shipped.
	ARR includes all reasons for returns (failures, handling damage, NDF), but
	does not include inventory credit returns.
Quality Acceptance Rate
< 1,000 DPPM	The quality acceptance rate indicates the percentage of Maxtor products
	successfully installed by our customers, and/or the number of defective parts
	per million (DPPM) encountered during the entire installation process.
Start/Stop Cycles
50,000	This indicates the average minimum cycles for reliable start/stop function.
Data Reliability
< 1 per 1014 bits read	Data errors (non-recoverable). Average data error rate allowed with all error
	recovery features activated.
Component Design Life
5 years (minimum)	Component design life is defined as a.) the time period before identified
	wear-out mechanisms impact the failure rate, or b.) the time period up to the
	wear-out point when useful component life expires.

3 – 4

Image 18

Contents DiamondMax Before You Begin U T I O NContents Product Specifications AT Interface Description Service and Support Figures Manual Organization IntroductionMaxtor Corporation AbbreviationsConventions DiamondMax 60 Key Features Product DescriptionModel CYL Product FeaturesFunctional / Interface MAX LBA CapacityCache Management Major HDA Components Subsystem Configuration Jumper Location / ConfigurationCylinder Limitation Jumper Description Performance Specifications Product SpecificationsDrive Configuration Models and CapacitiesPhysical Dimensions maximum Parameter A N D a R D MetricEPA Energy Star Compliance Power RequirementsPower Mode Definitions Environmental LimitsReliability Specifications Shock and VibrationParameter E R a T I N G Safety Regulatory Compliance EMC/EMIHandling and Installation Hard Drive Handling PrecautionsElectro-Static Discharge ESD Unpacking and Inspection Multi-pack Shipping ContainerPhysical Installation RepackingBefore You Begin Hook upSet up Start upAT Interface Description Interface ConnectorPIN Signal Pin Description SummaryPIN Name Signal Name Signal Description Pin Description TableTiming Parameters Mode PIO TimingDMA Timing Ultra DMA Timing Timing Parameters all times in nanosecondsSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Host Software Interface Task File RegistersPort Read Write N T E N T S LBA Bits Command Register Summary R a M E T E R S U S E DControl Diagnostic Registers Reset and Interrupt Handling Interface Commands Read Commands Read DMA Write Commands Write Multiple Mode Set/Check Commands Value DescriptionEV E L Value M M a N D Power Mode Commands Timer Value TIME-OUT PeriodSleep Mode Initialization Commands Content Description15 -3 = reserved R D Content Description Initialize Drive Parameters Seek, Format and Diagnostic Commands Error Code DescriptionA.R.T. Command Set Key RegisterNo Quibble Service Service and SupportService Policy SupportFrom Dial Glossary BlockCorrectableerror Fetch Landingzoneorlzone Physicalsector Softerror