Maxtor 94610H6, 93073H4, 96147H8, 91536H2, 92305H3 specifications Initialize Drive Parameters

Page 53

INTERFACE COMMANDS

Initialize Drive Parameters

Enables the drive to operate as any logical drive type. The drive will always be in the translate mode because of Zone Density Recording, which varies the number of sectors per track depending on the zone. Through setting the Sector Count Register and Drive Head Register, this command lets the host alter the drive's logical configuration. As a result, the drive can operate as any equal to or less than capacity drive type. Do not exceed the total number of sectors available on the drive:

When this command is executed, the drive reads the Sector Counter Register and the Drive Head Register (and so determines the number of the logical sectors per track and maximum logical head number per cylinder and will calculate the number of logical cylinders.)

Upon receipt of the command, the drive:

1.Sets BSY,

2.Saves the parameters,

3.Resets BSY and

4.Generates an interrupt.

To specify maximum heads, write 1 less than the maximum (e.g. write 4 for a 5 head drive). To specify maximum sectors, specify the actual number of sectors (e.g. 17 for a maximum of 17 sectors/track).

The sector count and head values are not checked for validity by this command. If they are invalid, no error will be posted until an illegal access is made by some other command.

Moves the read/write heads from anywhere on the disk to cylinder 0.

When this command is received, the drive:

1.Sets BSY and

2.Issues a seek to cylinder zero.

The drive waits for the seek to complete, then the drive:

1.Updates status,

2.Resets BSY and

3.Generates an interrupt.

If the drive cannot reach cylinder 0, the Error bit is set in the Status register, and the Track 0 bit is set in the Error register.

NOTE: If a maximum head and sector number is selected – such that the number of cylinders will exceed 65,535 – then the maximum cylinder value will be reduced to 65, 535.

7 – 13

Image 53
Contents DiamondMax U T I O N Before You BeginContents Product Specifications AT Interface Description Service and Support Figures Maxtor Corporation IntroductionManual Organization AbbreviationsConventions Product Description DiamondMax 60 Key FeaturesFunctional / Interface Product FeaturesModel CYL MAX LBA CapacityCache Management Major HDA Components Cylinder Limitation Jumper Description Subsystem ConfigurationJumper Location / Configuration Drive Configuration Product SpecificationsPerformance Specifications Models and CapacitiesParameter A N D a R D Metric Physical Dimensions maximumPower Mode Definitions Power RequirementsEPA Energy Star Compliance Environmental LimitsParameter E R a T I N G Reliability SpecificationsShock and Vibration EMC/EMI Safety Regulatory ComplianceElectro-Static Discharge ESD Handling and InstallationHard Drive Handling Precautions Multi-pack Shipping Container Unpacking and InspectionRepacking Physical InstallationHook up Before You BeginStart up Set upPIN Signal Interface ConnectorAT Interface Description Pin Description SummaryPin Description Table PIN Name Signal Name Signal DescriptionPIO Timing Timing Parameters ModeDMA Timing Timing Parameters all times in nanoseconds Ultra DMA TimingSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Port Read Write Host Software InterfaceTask File Registers N T E N T S LBA Bits Command Register R a M E T E R S U S E D SummaryControl Diagnostic Registers Reset and Interrupt Handling Interface Commands Read Commands Read DMA Write Commands Write Multiple EV E L Mode Set/Check CommandsValue Description Value M M a N D Timer Value TIME-OUT Period Power Mode CommandsSleep Mode Content Description Initialization Commands15 -3 = reserved R D Content Description Initialize Drive Parameters Error Code Description Seek, Format and Diagnostic CommandsKey Register A.R.T. Command SetService Policy Service and SupportNo Quibble Service SupportFrom Dial Block GlossaryCorrectableerror Fetch Landingzoneorlzone Physicalsector Softerror