Intermec PD4 manual Safety Warnings, Product Identiﬁcation

Page 13

Chapter 1—Introduction

Safety Warnings

•Read this manual carefully before connecting the printer.

•Moving parts are exposed when the side door is open, so ensure that the door is closed before you operate the printer.

•Do not open the front/left-hand cover. Dangerous voltage!

•Do not remove the bottom plate. Dangerous voltage!

•Do not put your ﬁngers inside the print mechanism when the power is on.

•Place the printer on an even surface which can support its weight of approximately 13 kg (28.7 pounds) plus supplies.

•Do not spray the printer with water. If you are using a hose to clean the premises in an industrial environment, remove the printer or pro- tect it carefully from spray and moisture.

•Carefully read the warning text on the envelope before using a clean- ing card.

Product Identiﬁcation

The machine label is attached to the printer’s rear plate and contains information on type, model, and serial number as well as AC voltage. It also contains various signs of approval.

Intermec EasyCoder PD4—User’s Guide

3

Image 13

Contents EasyCoder PD4 Bar Code Label Printer Page EMS and EMI Compliance Statement FCC Notice United States of AmericaIntermec EasyCoder PD4-User’s Guide Contents Adjustments TroubleshootingLoading Media Maintaining the PrinterMedia Speciﬁcations Technical DataBefore You Begin Safety SummarySafety Icons Warranty Information Web Support Telephone Support Global Services and Support Related Documents Introduction Description of EasyCoder PD4 Product Identiﬁcation Safety WarningsIntroduction Installation Unpacking the Printer Front View Rear View Media Compartment Print Mechanism Connections PowerComputer Control Lamps Controls and IndicatorsDisplay Control KeysKey Functions Mode Feed key Pause key Cancel keyInstallation Starting Up Switching On the Printer Direct Mode Printing a Test Label Loading Media Tear-Oﬀ Straight-through Flip the label feed guide upward Tear-Oﬀ,Rotation of the roll Align the media with the center section Tear-Oﬀ, Peel-Oﬀ Self-strip Screw Peel-Oﬀ,Peel-Oﬀ, Peel-Oﬀ, Thermal Transfer Printing Ribbon Load Ink outside the roll Ribbon Load,Loading Media Printing Controlling the Printing Navigating in the Setup Mode Setup MethodsKey label in display Function in the Setup Mode KeySetting review Setup Options Media TypeDensity SpeedPrinting Intermec EasyCoder PD4-User’s Guide Printing Options Stripper and Internal Rewinder Installation InstructionsSwitch Rewinder cable Cutter Cutter connector Cutter cable Cable clips Options Troubleshooting Description/Display Message Error HandlingAction Printing stops Command errors Error Suggested actionPrintout not in desired position Clearing Media Jam in Cutter Entering the Dump Mode Maintaining the Printer Printhead Cleaning Clean the printhead dot line External Cleaning Printhead Replacement Cut oﬀ any damaged or wrinkled part Media JamsAdjustments Engage the printhead and load the ribbon Printhead Balance AdjustmentPrinthead Pressure Adjustment Printhead Dot Line Position Adjustment Adjustments Label Gap Sensor Position Adjustment Label Gap Sensor Calibration Ribbon Tension Adjustment 1234567890 Ribbon Shield AdjustmentPage For media load Intermec EasyCoder PD4-User’s Guide Technical Data Table of Technical Data Physical Measures Power SupplyEnvironment ElectronicsData Interfaces Media Speciﬁcations Core Media Roll SizeInternal Roll Non-Adhesive Strip Media⇒ Liner Self-Adhesive Strip⇒ Label Length Self-Adhesive LabelsSELF-ADHESIVE Labels Feed Direction Tickets with Gaps Tickets & Tags Feed Direction ⇒ Black Mark Width Tickets with Black MarkTickets With Marks Feed Direction Interfaces RS-232 Interface DB-9 Signal MeaningProtocol Interface CableUSB Interface Pin Function Transmitter Comment Parallel InterfaceFirmware Upgrading Instructions RequirementsPage 960614-01